__color__,ticket,summary,component,version,milestone,type,owner,status,created,_changetime,_description,_reporter 3,994,Remove Chillispot Reaper process,fon-base-firmware,2.3.6.1 (Gari jr.),,bug,,investigate,2010-12-27T08:51:11Z,2013-02-14T21:18:44Z,"When connected on fonera 2100/2200/2201 I can have hotspot sessions over 18 hours and more without interruption. When connected to a Fonera 2.0n I will be disconnected within 2 hours and asked to relogon on fon.com; this makes games sessions that take a few hours not easy to play! The effect was documented as a Chillispot Reaper process which was installed in the Fon-ng firmware to make hotspots more ""stable""... it was destined to be removed but... is still there so it seems",steven@… 3,1106,Wifi restarts often when 3G signal low,fon-network-3g,2.3.7.0 beta2,,bug,,infoneeded,2011-10-19T05:55:37Z,2011-11-01T15:50:45Z,"F2G connected to internet on 3G dongle. No LAN cable plugged in (no internet nor intranet). Using wifi from a mobile device. 3G signal is at lower value and have some fluctuations, for short time it can disconnect then immediately reconnect. The problem: every time 3G is disconnecting/reconnecti4g the wifi interface is restarting ! This is not good at all because the device (e.g. smartphone) connected to wifi lose connection and must reconnect. All programs using that connections must be restarted (e.g. If I was listening to internet radio station I must reconnect first to wifi then search again for the radio station) My opinion is that the 3G disconnect/reconnect has to be transparent for the wifi user, not disturbed by wifi disconnects. Ticket #1105 may improve also this situation... p.s. Tested only on F2G. May be also a problem for F2N, but not tested.",mihaly.reg@… 3,1109,3G not reconnect after reboot,fon-network-3g,2.3.7.0 beta2,,bug,,investigate,2011-10-26T04:54:47Z,2013-02-10T21:38:43Z,"F2G with powered usb hub and huawei e160x dongle. Internet working fine. Reboot fonera from terminal. Error: after reboot 3G cannot reconnect. Umtsd state shows empty at provider and zero value for signal. 3G can be reconnected only by plugging out the usb cable from fonera, power down the usb hub then reconnect and power up. Tested only on F2G. ",mihaly.reg@… 3,1152,Wifi sometimes don't start after power on,fon-network,2.3.7.0 beta2,,bug,,investigate,2012-02-23T06:27:38Z,2012-03-24T12:12:25Z,"fonera 2g fw 2.3.7.0 beta2 usb hub and usb dongle huawei e160x connected wifi configured as open network, g only bridge configured started the router with power on 3g started wifi not started !!! this happens sporadically. sometimes wifi is starting, sometimes not this log is when wifi is not starting ",mihaly.reg@… 3,1300,"Dynamic DNS: freedns.afraid.org, URL escaping corrupts update code",fon-plugin-ddns,2.3.7.0 (Paco),,bug,,new,2013-05-14T13:17:20Z,2013-05-14T13:21:06Z,"When using the freedns.afraid.org dynamic dns service a update key is required. Example: EXAMPLEKEY-VMVVBQUg5aFdWOEFBQUFDOjk0Nzc1NzM= The update URL is built using a hardcoded part + the key which is inserted instead of a placeholder. The URL then is being escaped which corrupts the update key (in this example the equal sign is replaced by '%3D' ). Since all my update keys contain a '=' I am unable to use the dyndns feature with freedns.afraid.org. ",Tristan Helmich 3,542,usb / samba / torrent / network drive problems,fon-base-firmware,Other,,bug,,testnewer,2009-12-29T20:31:36Z,2010-06-18T12:05:20Z,"F2N 2.3.5.0 bridge. 1.5T USB disc with 3 partitions, Disc-A1 A2 A3. A1 A2 is EXT2, A3 is FAT32. Torrent used on A1, samba activated, ftp activated. After using a while torrent, network drive A1 A2 the router is going crazy. Some features are accessing the disc, others not. 1. Accesing from network: \\192.168.0.2 is displaying Disc A1 A2 A3. Only A1 A2 accesible inside the folder. 2. Accesing from network: \\192.168.0.2\Media only A1 A2 is displayed. 3. F2 GUI the USB disc is not shown 4. Torrent is working and seeding, accessing files from A1 5. Fon file browser is displaying A1 A2 6. From local network A1 A2 can be accessed. 7. A lot of smbd processes are running with different PIDs. PIDs cannot be killed, like stated in previous ticket.",mihaly.reg@… 3,561,WEP support broken on Fonera 2.0n: 2.2.6.0-2.3.5.0,fon-wifi,Other,,bug,john.crispin@…,testnewer,2010-01-19T11:44:28Z,2010-06-08T14:37:53Z,"Hello! I tried to enable 64&128 WEP encryption with Fonera 2.0n (two units). I loaded firmwares 2.2.6.0, 2.3.0.0 and 2.3.5.0. WPA encryption works normally, but I need WEP because of compatibility with older devices and there are some performance issues with WPA. This is for a multi AP network with roaming support. Description of the bug: When setting a WEP encryption with key, my Windows notebook comes up with this error: ""Windows is unable to connect to the selected network. The network may no longer be in range. Please refresh the list of available networks and try to connect again."" Instead, it should ask me for the WEP key! Tried and rebooted several times. With other APs, WEP works normally. With 2.0n, it also works with WPA. I tried to set up the wireless.public.key=1, and .key1=ACTUAL_KEY (also with config.sh script from uci fon), but still doesn't work. Other wireless devices would detect WEP network, ask me for the key, but none would get accepted. I could not access the actual WEP settings from the Ralink chip, as iwlist doesn't work fully. Proposed solution: check what WEP settings do actually get sent to the Ralink wireless chip. It should be easy to key in a 64-bit WEP (also with leading zeroes) and get it to work withing a minute.",zencoslav@… 3,598,"UMTS works, GPRS fails with Huawei E220 on Fonera 2.3.0.0-DEV",fon-network-3g,2.3.0.0 (Elan),,bug,,investigate,2010-03-06T18:40:36Z,2012-12-19T17:13:44Z,"I'm trying to setup my fonera for home use. At the office I have an excellent UMTS-Signal. The fonnera connects without any problems. At home I only have an good Edge-signal. The fonera is ""dialing in""... thats all. Any logs or missing informations can be provided on request. I tried a lot of diagnosis...",mandolyn@… 3,828,fon.com is sooooooo slow,fon-web,Other,,bug,john.crispin@…,confirmed,2010-06-09T14:34:07Z,2013-03-25T14:52:44Z,"It takes almos 15-20 second to get logged into your fon.com account to check your profile. Couldn't it be a little faster? ",decodecoding@… 3,839,Firewall not working in bridge mode,fon-network,2.3.6.0 (Gari),,bug,john.crispin@…,confirmed,2010-06-23T16:05:32Z,2012-12-20T12:43:06Z,"When in bridge mode, the (wan) firewall settings are not working. Every port is open by default, since there is no separate WAN zone anymore. There are still rules generated in the input_daemon chain, but those point to zone_wan_ACCEPT and zone_wan_REJECT which are empty. Additionally, the SSH hammering protection stops working in bridge mode. All of this is sort of expected, but it would be nice if we could still distinguish a WAN zone in bridge mode, for example by matching the LAN ip subnet into the LAN zone and putting all of the other addresses in the WAN zone.",matthijs 3,878,Duplicate html
tags when using SimpleForms,fon-base-firmware,2.3.6.0 (Gari),,bug,,confirmed,2010-08-17T14:08:05Z,2010-08-17T14:08:40Z,"While debugging #644, it became apparent that in some cases, there are duplicate (nested) form tags. The particular problem in #644 has been fixed, but this duplication might need some cleanup later on. For now, we'll leave this be, since it works and will require a fairly invasive change to luci requiring lost of testing. Here's the original comment describing the problem: Furthermore, it seems that the HTML generated for SimpleForm is broken, it includes the header and footer with the and
tags twice (once from header.htm and footer.htm included by dispatcher.lua and once directly from the simpleform.html template. r504 tried to fix this for the Wizard (which uses SimpleForm), but this fix is incomplete since it doesn't suppress the footer (the wizard still contains double tags) and it doesn't fix other uses of the SimpleForm. This fix is also not really the right way to fix this either, since it needs noheader/nofooter settings in the controller, depending on whether Map of SimpleForm was used in the cbi files. AFAICS, the proper fix for this problem would be to just remove the header/footer stuff from simpleform.htm and rely on the header and footer included by dispatcher.lua always. A bit more reading shows that this is exactly what the Form class (a subclass of SimpleForm) does by setting the ""embedded"" attribute, which supresses the header and footer of the simpleform.htm template. Using Form for the Firewall -> Applications page also fixes the cancel button (though I've not completely grasped why yet). However, in the wizard, just changing to Form might not be enough. In particular, the downloadmanager wizard steps already use the Form class, but explicitly include the map_head.htm template (for example at the bottom of dlmanager_mu.lua). So perhaps the noheader is still appropriate here (since the dlmanager_mu.lua also includes the custom wizard head and head_darkorange, which are normally included via header.htm from fon.lua (but the latter contains an override not to include any header in the wizard). So in the end, most of it works out, but here and there there a few duplicate headers or footers. Changing from SimpleForm to Form is probably fine everywhere outside of the wizard. In the wizard, things look a bit more complicated, I'm not sure what the best fix for that is (since there still are some duplicate footers in the SimpleForm cases). ",matthijs 3,971,recover connected discs at boot,fon-base-firmware,2.3.6.1 (Gari jr.),,bug,,investigate,2010-11-15T16:57:12Z,2012-12-20T14:33:19Z,"The fonera doesn't unmount when re Nov 15 16:52:01 Fonera user.crit kernel: EXT2-fs error (device loop2): ext2_get_inode: unable to read inode block - inode=1281, block=8236 Nov 15 16:52:01 Fonera user.info kernel: attempt to access beyond end of device booting, but at next boot it will have issues due to unproper journal... a manual ef2chk -a /dev/sda2 is required :( Nov 15 16:52:01 Fonera user.crit kernel: EXT2-fs error (device loop2): ext2_get_inode: unable to read inode block - inode=1281, block=8236 Nov 15 16:52:01 Fonera user.info kernel: attempt to access beyond end of device ",steven@… 3,976,USB Disk mounting is unstable,fon-base-firmware,2.3.6.1 (Gari jr.),,bug,,investigate,2010-11-19T09:22:18Z,2013-04-26T11:10:10Z," I need often to reboot my Fonera 2.0n (Gari jr. installed) because the USB disk is often not visible through FTP, Samba and Fonera's web GUI. After I reboot the Fonera the disk is again visible and all works fine. PS. I normally access the Fonera through WAN port. ",rughis 3,1027,kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 erro using SPB TV,fon-base-firmware,2.3.6.1 (Gari jr.),,bug,,infoneeded,2011-03-27T13:46:11Z,2012-12-19T08:29:36Z,"I'm running SPB TV streaming on Nokia E72 device connected by wifi to fonera 2.0n, fw 2.3.6.1, bridge mode, wifi g tkip aes. Stream is coming on udp. Stream start fine, but soon stops, have to restart SPB TV app, then starts again and stops. logread on fonera: Mar 26 20:33:51 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:34:01 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:37:26 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:38:30 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:39:16 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:39:36 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:40:34 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:40:56 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:43:56 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:46:12 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:46:56 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:46:56 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:47:40 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:47:47 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:47:54 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:47:54 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:49:32 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:51:19 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:51:36 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:51:36 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 Mar 26 20:51:39 Fonera user.warn kernel: DWC_OTG_HC_XFER_FRAME_OVERRUN: 8 ",mihaly.reg@… 3,1117,Unstable USB disk,fon-base-firmware,2.3.7.0 (Paco),,bug,,investigate,2011-11-09T20:36:59Z,2013-01-14T14:29:02Z,"Prevent change Disc-A1 to Disc-B1 ? I'm using F2G with a 3G dongle and a flash drive. Sometimes when I insert the flash it appears Disc-A1 and sometimes Disc-B1. How can I prevent this, to have always Disc-A1 or some other name but always the same ?",mihaly.reg@… 3,1118,Crashed 3G cannot recover automatically,fon-network-3g,2.3.7.0 beta2,,bug,,investigate,2011-11-09T20:41:56Z,2012-12-20T17:45:30Z,"F2g used with 3G dongle. If 3G crashes for whatever reason it cannot recover/reconnect automatically, a power cycle is needed. ",mihaly.reg@… 3,1124,3G killed after most 12 hours,fon-network-3g,2.3.7.0 beta2,,bug,,investigate,2011-12-01T08:14:27Z,2012-12-18T14:47:24Z,"Using F2G with huawei 160x 3G dongle with unlimited data plan. No other option conneted to fonera. Accessing internet only from wifi smartphones. The 3G connection never stay online more then 12 hours, it's killed and does not reconnect. A secondary effect is that wifi is also killed. I could capture a logread only until wifi was disconnected, see attached.",mihaly.reg@… 3,1145,b/g/n mix mode not working,fon-wifi,2.3.7.0 beta2,,bug,,infoneeded,2012-01-31T11:55:08Z,2012-12-12T11:54:12Z,"b/g/n mix mode not working and show only b/g bands,/n band is missing,transver speed is slow,in /n mode only is ok and fast and shows like /n conecction. fix b/g/n mix mode please.sory for bad english",mnezirov@… 3,1149,/var/state/umtsd filling up over time,fon-network-3g,2.3.7.0 beta2,,bug,,investigate,2012-02-10T07:16:54Z,2012-12-20T17:47:31Z,After about 10 hours of online state of f2g the file var/state/umtsd is filled with a lot of records that normally are not there at startup. I guess that this triggers later the lockup of fonera. ,mihaly.reg@… 3,1162,network bridge fails regularly,fon-network,2.3.7.0 beta2,,bug,,infoneeded,2012-03-21T12:21:59Z,2012-12-20T17:53:56Z,"Since I connected something to the usb port of the device; the fonera's bridging capability seems to fail regularly; I have several devices connected to the lan ports; and they don't get an ip from the dhcp server located on the wan of the device the fonera is configured in bridge a reboot of the fonera works ",steven@… 3,1171,Supported Webcam via supported USB 2.0 Hub unsupported,fon-plugin-webcam,2.3.6.1 (Gari jr.),,bug,,infoneeded,2012-05-22T16:07:59Z,2012-12-20T17:57:38Z,"I have Microsoft Lifecam which works fine on my Fonera 2.0n when I attach it on the single USB port. Now I attached a USB 2.0 hub (self powered) and attached the webcam to the hub now. Suddenly no video is returned anymore but external harddrives and flash disks work. /proc/bus/usb/devices: {{{ T: Bus=01 Lev=03 Prnt=03 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(unk. ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=045e ProdID=075d Rev= 1.05 S: Manufacturer=Microsoft S: Product=Microsoft® LifeCam Cinema(TM) C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(unk. ) Sub=01 Prot=00 Driver=uvcvideo E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=16ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo I: If#= 1 Alt= 1 #EPs= 1 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 128 Ivl=125us I: If#= 1 Alt= 2 #EPs= 1 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 256 Ivl=125us I: If#= 1 Alt= 3 #EPs= 1 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 512 Ivl=125us I: If#= 1 Alt= 4 #EPs= 1 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=1024 Ivl=125us I: If#= 1 Alt= 5 #EPs= 1 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=2048 Ivl=125us I:* If#= 1 Alt= 6 #EPs= 1 Cls=0e(unk. ) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=3072 Ivl=125us I:* If#= 2 Alt= 0 #EPs= 0 Cls=01(audio) Sub=01 Prot=00 Driver=(none) I:* If#= 3 Alt= 0 #EPs= 0 Cls=01(audio) Sub=02 Prot=00 Driver=(none) I: If#= 3 Alt= 1 #EPs= 1 Cls=01(audio) Sub=02 Prot=00 Driver=(none) E: Ad=82(I) Atr=05(Isoc) MxPS= 256 Ivl=1ms }}} dmesg for removing -> attaching camera on hub: {{{ hub 1-1.4:1.0: state 7 ports 4 chg 0000 evt 0004 hub 1-1.4:1.0: port 2, status 0100, change 0001, 12 Mb/s usb 1-1.4.2: USB disconnect, address 4 usb 1-1.4.2: unregistering device usb 1-1.4.2: usb_disable_device nuking all URBs usb 1-1.4.2: unregistering interface 1-1.4.2:1.0 usbdev1.4_ep83: ep_device_release called for usbdev1.4_ep83 usb 1-1.4.2:1.0: uevent usb 1-1.4.2: unregistering interface 1-1.4.2:1.1 usbdev1.4_ep81: ep_device_release called for usbdev1.4_ep81 usb 1-1.4.2:1.1: uevent usb 1-1.4.2: unregistering interface 1-1.4.2:1.2 usb 1-1.4.2:1.2: uevent usb 1-1.4.2: unregistering interface 1-1.4.2:1.3 usb 1-1.4.2:1.3: uevent usbdev1.4_ep00: ep_device_release called for usbdev1.4_ep00 usb 1-1.4.2: uevent hub 1-1.4:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 hub 1-1.4:1.0: state 7 ports 4 chg 0000 evt 0004 hub 1-1.4:1.0: port 2, status 0101, change 0001, 12 Mb/s hub 1-1.4:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 usb 1-1.4.2: new high speed USB device using dwc_otg and address 6 usb 1-1.4.2: skipped 1 descriptor after configuration usb 1-1.4.2: skipped 6 descriptors after interface usb 1-1.4.2: skipped 1 descriptor after endpoint usb 1-1.4.2: skipped 28 descriptors after interface usb 1-1.4.2: skipped 1 descriptor after endpoint usb 1-1.4.2: skipped 4 descriptors after interface usb 1-1.4.2: skipped 2 descriptors after interface usb 1-1.4.2: skipped 1 descriptor after endpoint usb 1-1.4.2: default language 0x0409 usb 1-1.4.2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-1.4.2: Product: Microsoft® LifeCam Cinema(TM) usb 1-1.4.2: Manufacturer: Microsoft usb 1-1.4.2: uevent usb 1-1.4.2: usb_probe_device usb 1-1.4.2: configuration #1 chosen from 1 choice usb 1-1.4.2: adding 1-1.4.2:1.0 (config #1, interface 0) usb 1-1.4.2:1.0: uevent uvcvideo 1-1.4.2:1.0: usb_probe_interface uvcvideo 1-1.4.2:1.0: usb_probe_interface - got id uvcvideo: Found UVC 1.00 device Microsoft® LifeCam Cinema(TM) (045e:075d) usb 1-1.4.2: adding 1-1.4.2:1.1 (config #1, interface 1) usb 1-1.4.2:1.1: uevent usb 1-1.4.2: adding 1-1.4.2:1.2 (config #1, interface 2) usb 1-1.4.2:1.2: uevent usb 1-1.4.2: adding 1-1.4.2:1.3 (config #1, interface 3) usb 1-1.4.2:1.3: uevent drivers/usb/core/inode.c: creating file '006' }}} Any ideas on how to fix this?",Jasper 3,1235,channel XXX: open failed: unknown channel type:,unknown,2.3.7.0 rc2,,bug,,infoneeded,2012-11-28T09:00:54Z,2012-12-10T13:02:46Z,"Hi, This problem only occurs when using Fonera as a Proxy through SSH. Browsing starts to slow down and finally fails to get web pages. I have 2.3.7.0 RC2 installed with Tinyproxy 1.8.2 built by myself. I have also tried with 2.3.7.0 beta 3 and RC1 and Tinyproxy 1.6.4 from http://downloads.openwrt.org/kamikaze/8.09.2/rb532/packages/. The problem arises after using the configuration explained above: Connecting LaFonera through SSH and using Tinyproxy as a proxy. After browsing a little (few minutes) at the console of SSH begins to show multiple messages: channel XXX: open failed: unknown channel type: If i restart tinyproxy things starts to run again, but after few minutes it returns. I have been using LaFonera with this scenario long time ago. There have been any changes in my Fonera configuration, only the location from I connect to SSH. Accessing internet from this location without proxy don't show any problem. There is no problem also when using internet connected at home directly to LaFonera. My OS is Ubuntu 12.10. Firefox 17.0 and Firefox Nightly 20.0. I don't know the way of debugging the problem, could you tell me some steps to try to search where the problem is?. Regards. ",diaz8@… 3,1236,Picasa upload does not always work.,fon-plugin-picasa,2.3.7.0 rc2,,bug,,infoneeded,2012-12-11T10:04:38Z,2012-12-12T09:36:33Z,"On the blog, [http://blog.fonosfera.org/2-3-7-0-rc2/#comment-237250 Charudatt reports] that Picasa uploads are not working for him: > Picassa uploader does not seem to be working, gives an error , but > shows as done, and tweets too. > I tried entering my credentials but did not work. The Fonera Dashboard > shows uploading, at the very end of the progress bar shows an error , > creates a folder called DONE and creates some files done_picasa, I > also get a tweet, saying that I have successfully uploaded it (becos , > I have enabled it) , but nothing gets uploaded. Charudatt, two more questions: You say ""entering your credentials did not work"". Do you mean that the credentials were not accepted (input fields turn red after clicking save), or do you mean re-entering the credentials did not help to fix the upload problem. Could you try logging in with SSH, run the ""logread"" command shortly after a failed upload and attaching / pasting the output here? See [wiki:reportbugs] for more info on running commands on your Fonera. ",matthijs 3,1246,Fonera 2.0n N encryption problem,fon-wifi,2.3.7.0 (Paco),,bug,,infoneeded,2013-01-23T18:16:45Z,2013-02-08T14:47:31Z,"Hello, I have problem connecting anything (from PC to tablet, phone or console)to my FON2303 when it's configured as N only with any encryption. On N it's accept connection only if open without encryption. On B or G, no problem detected. I installed various firmwares, the last one is 2.3.7.0 without success. In order to use the router, I have to run it on G only. I tried (when in N only) to change channel, encryption or any other setting without luck. I make a factory reset and restored with the 2.3.0.0_restore firmware but still it do not work on N network.",gabriele.cozzi@… 3,1247,Samba share problem with Fonera 2202 on Windows,fon-base-firmware,2.3.7.0 (Paco),,bug,,confirmed,2013-02-12T12:14:54Z,2013-02-12T12:33:00Z,"When I share a USB HDD I can see and use the files on it using my Windows clients. If I do a DIR command (using either CMD.EXE or COMMAND.COM) it does show me all the files on the share correctly. However if I use wildcards, for instance doing a DIR *.TXT (and ofcourse there are a number of .TXT files present) no files are shown and File Not Found is the error message shown by the DIR command. (.TXT is just an example, any (part of) the filename, any extension and any combination of the two wildcards * and ? always delivers the samen result: file not found). Have a look: {{{ Z:\Disc-A1>dir Volume in drive Z is Media Volume Serial Number is 00AE-044F Directory of Z:\Disc-A1 01-01-1601 01:00 . 21-04-2009 16:21 .. 20-09-2012 23:00 Office 2007 24-01-2008 19:21 1.086.613 PowerISO39.exe 14-08-2007 00:45 484 PowerISO39.txt 11-11-2012 20:12 Ilse de Lange - Eye Of The Hurricane 29-10-2012 14:31 662.016 Presentatie 15-11-2012.pps 18-11-2012 00:05 nhc 01-06-2011 16:38 9.938.313 EZ Gig IV for Windows.exe 04-12-2012 14:30 4.494.456 sp34152.exe 06-01-2013 17:59 4.653.060 fonera.img 6 File(s) 20.834.942 bytes 5 Dir(s) 15.036.416 bytes free Z:\Disc-A1> }}} Good, let us now try to only filter out the .exe files: {{{ Z:\Disc-A1>dir *.exe Volume in drive Z is Media Volume Serial Number is 00AE-044F Directory of Z:\Disc-A1 File Not Found Z:\Disc-A1> }}} What gives? File Not Found? Are you kidding me? I have tried an awful lot: - I have tried a minimal smb.conf - I have tried different codepages (437, 850, ASCII, UTF8...) - I have installed an older (2.x) version of Samba on the FON2202 - I have tried it on a share of the root of the FON2202 instead of /tmp/mounts - I have tried other USB devices - I have tried almost all relevant smb.conf parameters and combinations of them - I have tried uppercase, lowercase, all sorts of combinations of wildcards (*,?) - I have tried flipper and paco on the FON2202 to no avail; always File Not Found whenever I use wildcards from a command prompt on a samba share using DIR, COPY, DEL or any other command that accepts wildcards. And I desperately need wildcards in my batch files... Windows itself works fine; any dialog box that allows filtering using wildcards works fine (for instance notepad.exe when opening a file allows to specify wildcards in its file open dialogue box). So it must be some combination between the command interpreter under Windows (as I said; both COMMAND.COM as well as CMD.EXE show this odd behaviour), Windows XP SP3, CIFS and the Samba/OpenWRT config on the FON2202 that is causing this. I have two other small Linux boxes here running Samba (2.x and 3.x) and on these machines it all works as expected... i.e. it can't be my Windows clients. It must have something to do with Samba or OpenWRT on the FON2202. --- The above was reproduced by Mathijs Kooijman which he mentioned in a reply to the above on development@fonosfera.org on Feb 8th, 2013. Apparantly it is a kernel bug introduced between 2.6.21 and 2.6.26 He asked me to report the bug here. --- ",ernstoud@… 3,1251,"openvpn ""safe surf"" dns resolution doesn't work",fon-plugin-openvpn,2.3.7.0 rc1,,bug,,infoneeded,2013-03-12T20:51:53Z,2013-03-13T10:27:53Z,"in file /etc/init.d/openvpn you can find the following code: {{{ [ ""$WAN"" = ""1"" ] && { DNS=`uci get fon.lan.ipaddr` PUSH=""--push \""dhcp-option DNS $DNS\"" --push \""redirect-gateway bypass-dhcp\"""" } }}} however, this code does seem to be wrong. the code that correctly works for me is: {{{ [ ""$WAN"" = ""1"" ] && { DNS=`uci get fon.wan.dns` PUSH=""--push \""dhcp-option DNS $DNS\"" --push \""redirect-gateway bypass-dhcp\"""" } }}} this will use the external dns servers which - other than the localhost - correctly resolve external domainnames. ",Thomas Horner 3,1259,"Transmission keeps restarting while ""rejecting IO to dead device"" messages appear",fon-base-firmware,2.3.7.0 (Paco),,bug,,infoneeded,2013-04-06T08:14:31Z,2013-04-24T11:13:24Z,"logread shows this on my fonera: {{{ Apr 6 07:08:31 Fonera user.err kernel: scsi 0:0:0:0: rejecting I/O to dead device Apr 6 07:08:31 Fonera user.err kernel: scsi 0:0:0:0: rejecting I/O to dead device Apr 6 07:08:31 Fonera user.notice root: transmission has stopped Apr 6 07:08:31 Fonera user.notice root: starting transmission Apr 6 07:08:31 Fonera user.err kernel: scsi 0:0:0:0: rejecting I/O to dead device Apr 6 07:08:31 Fonera user.err kernel: scsi 0:0:0:0: rejecting I/O to dead device Apr 6 07:08:31 Fonera user.err kernel: scsi 0:0:0:0: rejecting I/O to dead device }}} The scenario is not clear at this time, I have not used/accessed the fonera for a while. Today logged in and looked at logread for another problem. Transmission was not running torrents, was just installed some time ago. I had seen this error also a couple of months ago, but not sure which version was. Opened this ticket just to not forget about the problem. Will add more info later. ",tman 3,1297,Printer Plugin loop All internet,fon-plugin-printer,2.3.7.0 (Paco),,bug,,infoneeded,2013-04-21T20:46:53Z,2013-04-29T11:50:16Z,"Hi, i am using fonera 2.0n 2.3.7.0 and printer plugin, i have a printer HP Photosmart C5280 All-in-one that when i start to print every tipe of document, it block all internet froma any pc, until the printer end to print. i remember with later fw this problem was not here. This issue started with the latest firmware/plugins",xion87@… 3,1299,Loss of LAN ports on FONERA 2n with ONKYO TX-NR414 connected,fon-base-firmware,2.3.7.0 (Paco),,bug,,investigate,2013-05-08T07:43:18Z,2013-05-23T06:52:03Z,"With my FONERA 2n (f/w 2.3.7.0) in ""bridge"" or ""wifi bridge"" mode the following situation occurs. Also true in DHCP mode 1. Power up Fonera, then power up NR414 - LAN led on, connection made. 2. Power off NR414 and power it up later - LAN led off, no connection. 3. While the NR414 is powered up transfer the Ethernet cable to another LAN port and the LED comes on and the connection is made. 4. This process (i.e. points 2. and 3.) can be repeated until all 4 LAN ports are ""dead"". 5. Power cycle the Fonera and all LAN ports become available. ",cmford@… 3,498,"Deselected ""fwbrowser"" in menuconfig, but link still there in LuCI",unknown,Unknown,Firmware 2.3,bug,iurgi@…,investigate,2009-12-12T20:48:04Z,2012-12-19T15:23:31Z,"I have compiled a firmware where I disabled the ""fwbrowser"" option. But now, LuCI still shows ""file manager"" and ""drives"" options. I though that ""fwbrowser"" removed them?!",carsten.schuette@… 3,672,The fonera fails to spin up idle HDDs,fon-base-firmware,2.3.6.0 (Gari),Firmware 2.3,bug,,investigate,2010-04-21T15:21:26Z,2010-07-23T18:49:20Z,"Hi! My (newly bought, netadapter:d) HDD doesn't spin up when entering Windows wich results in an: ""can not reconnect to network place"" (or something like that) error message. I need to manually go into ""my computer"" and click on the drive to get it going every time wich is VERY annoying. This together with the Ticket #652 problem makes the Fonera more or less unusable in Windows I think. The same problem occurs when trying to accessing the FTP server when the HDD is idle. The user is logged in to the server but no folders are found. You need to disconnect from the server, wait a few seconds (until the HDD is ""spinned up"") and then logon again to be able to access the folders (or constantly hit the F5 button for 10-15 seconds). This procedure is hard to explain to an ordinary FTP user! When will these things be fixed?? I'm using the latest hummingbird firmware and Win 7.",henke81@… 3,855,Low throughput using FTP/Windows Networking and USB disk,fon-base-firmware,2.3.6.0 (Gari),Firmware 2.3,bug,,investigate,2010-07-09T16:02:37Z,2013-05-16T10:31:00Z,"I have a Fonera 2.0n with a 1,5TB harddisk. When I put my 1,5TB harddisk in the USB port of my Windows 7 PC, I get around 25MB/s ( MegaByte not Megabit! ). When I try to copy something from the harddisk that uses the USB port on the Fonera 2.0n its lower than 1MB/s. Very Slow... PC to PC transfer goes faster (network transfer) with 10MB/s. Can you please speed this up so it will be around 7MB/s or higher in the future! I would like to see this in new firmware. If File transfer is already faster with DEV firmware, please respond to this ticket. Sorry for my bad English :)",calvinturbo@… 3,880,"Upload to flickr / facebook from filebrowser creates ""done"" directory with empty files",fon-plugin-flickr,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,confirmed,2010-08-18T12:53:43Z,2010-09-02T15:08:32Z,"When you select a file for upload to Flickr or Facebook from the filebrowser, the file is uploaded. However, a new folder called ""done"" is created at same place where the uploaded file resides. Inside, an empty file is created with s similar name as the uploaded file. The uploaded file itself is unchanged. This is probably useful inside the ""flickr"" folder, to keep track of which files are uploaded already. However, for files manually queued for upload, this isn't really needed (and litters the disk with ""done"" directories). This problem was reported by OldMan and confirmed by me for the flickr uploader. I've confirmed this on both 2.3.6.0 and 2.3.6.1.",matthijs 3,901,3G connection does NOT reflect traffic utilization in Dashboard >> Status panel,fon-network-3g,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,investigate,2010-09-02T11:01:50Z,2013-02-15T05:31:06Z,"In fonera web interface there are a panel (Dasboard >> Status) when you can obtain graphics of network utilization. If you use a 3G connection, in WAN gaphic you can't see traffic utilization.",Dan 3,902,Transmission settings issue after reboot,fon-plugin-transmission,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,confirmed,2010-09-03T12:41:21Z,2010-09-03T17:47:50Z,"I setted upload and download limits on the preferences pane of the transmission webui. After reboot my settings was gone.",tas@… 3,948,SSID with spaces accepted without errors but only first word really recognized,unknown,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,investigate,2010-10-22T08:29:00Z,2011-10-17T11:04:16Z,"This bug is here for a long time, I hoped that someone noticed but now I'm reporting myself. If i set an SSID on the private network that contains spaces between words (possible in every other router that I know) the name is accepted without errors but the real SSID is only the first word specified. ",anonymous 3,959,Trust Webcam not working,fon-plugin-webcam,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,investigate,2010-11-03T13:00:56Z,2012-12-19T16:25:47Z,"On the list of supported webcams, this one is - so I bought it... However when I enable it and connect it, I just get a white box with ""failed to connect to server (denied?)"" ",rob_bot@… 3,968,"Upgrade page says ""45 minutes"" for both 2.0g and 2.0n",translations,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,confirmed,2010-11-12T00:43:31Z,2011-05-23T21:03:50Z,"In the fonera 2.0n the countdown starts from 5 minutes. (This value is wrong in all languages)",giuseppeg88@… 3,1009,Sentence not localized in the application installation,translations,2.3.6.1 (Gari jr.),Firmware 2.3,bug,,confirmed,2011-01-15T12:47:12Z,2011-01-17T17:07:23Z,"As shown in the image: ""Install on"" isn't localized.",giuseppeg88@… 3,1067,printer server does not worked immediately after updating to 2.3.7.0 beta,fon-plugin-printer,2.3.7.0 beta1,Firmware 2.3,bug,,investigate,2011-08-15T11:36:54Z,2012-10-31T06:16:40Z,"I made an update from 2.3.6.1 to 2.3.7.0 beta. I added the printer application in dashboard/application (All the applications are deactivated after update) I attached my printer (canon ip3600) and turned it on. Well nothing happend. The printer icon in the dashboard does not activaes itself. I even tried to print a test page and still nothing happend. I restarted the fonera and the printer has been recognized and was able to print. It seems to me that the fonera needs to be rebooted after installing the printer plugin. Regards alexb","fon2@…, com" 3,1078,music plugin does not play specific mp3 files/streams,fon-plugin-music,2.3.7.0 beta3,Firmware 2.3,bug,,confirmed,2011-09-02T15:54:48Z,2012-12-20T17:24:04Z,"I installed music plugin in firmware 2.3.7 beta and it doesn't work. When I want to listen music or insert a link to a stream server it says that is an invalid stream or 'Audiod is not running Audiod, the music playing application, does not seem to be running right now. This usually indicates it has crashed or was never started. It will probably help to unplug and replug your USB audio card to restart audiod.' If I connect to fonera by SSH and try to start audiod shows the text above: {{{ root@Fonera:~# audiod scanning for audio channel found VOLUME skipping found PCM using channel id 4 found SPEAKER skipping found PCM skipping found ALTPCM skipping found PHONEOUT skipping we have a client! About to add fd 6 Client 6 disconnected we have a client! About to add fd 6 Client 6 disconnected we have a client! About to add fd 6 Client 6 disconnected we have a client! About to add fd 6 Client 6 disconnected we have a client! About to add fd 6 got token -> ""STOP"" got token -> ""LIST"" loading /tmp/myplaylist.m3u found an entry ""/tmp/mounts/kasaHD/music/VA-As.40.da.Cidade.FM-2010-UpPTMSNM (05-02-2011)/VA-As.40.da.Cidade.FM-2010-UpPTMSNM (05-02-2011)/Afrojack Eva Simons - Take Over Control.mp3"" loaded /tmp/myplaylist.m3u got token -> ""MODE"" got token -> ""START"" playing file : /tmp /tmp/mounts/kasaHD/music/VA-As.40.da.Cidade.FM-2010-UpPTMSNM (05-02-2011)/VA-As.40.da.Cidade.FM-2010-UpPTMSNM (05-02-2011)/Afrojack Eva Simons - Take Over Control.mp3 scan_mp3(): fixed rate mp3, time 2147483647, num frames 2147483647 duration is = -2126008813 Segmentation fault }}} Simultaneosly I go to fonera and try to play a music until the message Segmentation fault is shown in the ssh connection... I tried to insert the following links for stream server http://sradio.tv/asx/1090.asx http://sradio.tv/stream/1090.m3u Can you help me?",micaelopes@… 3,1116,WiFi range too low,fon-wifi,2.3.7.0 beta2,Firmware 2.3,bug,,investigate,2011-11-09T15:04:50Z,2012-12-20T17:37:34Z,"Both F2g and F2n have a very low wifi range, a couple of meters inside the building. F2n tested with a windows xp pc with wireless g adapter, it shows signal 30% at 6 meters distance, and sporadically disconnects. F2n tested with nokia mobile, wifi G, it disconnets at about 10 meters. F2g tested with nokia mobile, wifi G, disconnets at 10 meters. Is there a command or configuration to increase power of wifi ? ",mihaly.reg@… 3,1194,No WebGUI logout from WAN,fon-web,2.3.7.0 beta3,Firmware 2.3,bug,,investigate,2012-06-29T11:34:39Z,2012-08-21T13:22:57Z,"Logout from WebGUI when accessing from Internet (WAN) is not possible. After pressing the ""Logout-button"" you keep logged in. I tried accessing with different browser, by using DynDNS (dyndns.org) and direct by WAN-IP.",shareAir.net 3,1226,2.3.7.0rc1 | Bei Wlan-Auswahl von nur g-Modus ist MyPlace nicht erreichbar,fon-wifi,2.3.7.0 rc1,Firmware 2.3,bug,,infoneeded,2012-10-07T09:29:07Z,2012-12-27T19:19:03Z,,Micha 3,1230,Transmission not responsive when a load of files are added (?),fon-plugin-transmission,2.3.7.0 rc1,Firmware 2.3,bug,,infoneeded,2012-10-16T11:34:03Z,2012-12-27T19:18:47Z,"Hi, there! I used to have the 2.3.6.1 version with about 70 torrent files running continuously on my fonera 2.0n. I used remote transmission and was able to deal with it very easily. After the update to 2.3.7.0RC1 I noticed that the new transmission did not recognize the old ""torrent list"" after I installed the app in the same partition of my fonera attatched disk. I figured this was because of the update on transmission version, and tried re-uploading the files (or most of them...about 50 in a row). I unchecked the ""start torrent"" as I wanted the fonera to simply check for the files availability at firs. It worked for some hours, in which I even was able to check the torrnents status (and follow the ""verifying"" stage) through remote transmission gui. But the next day, something had apparently gone wrong and the transmission access was cut. I tried rebooting the fonera for several times unsuccessfully. The most annoyng thing is that I can't even open web transmission nor stop the app via the fonera dashboard (where I see the message ""torrent is currently running"" but can't see the neither of the files nor the options to shutdown the app.) I will now try to re-install the RC1 and see if that gets my fonera a new ""blank list"" of torrents. I think this might be some sort of a bug when trying do deal with multiple torrent uploads.. maybe the fonera just can't handle the exhausting verifications that follow. All my torrents were/are from a single tracker: torrentleech, and I've never had problems before RC1, apart from some weird ""apparently"" disconected disk, that wouldn't let me access the files through network unless I rebooted the fonera, after which the problem would be over. Thank you.",semogleunam@… 3,1242,Samba access denied on 2.3.7.0 Paco,fon-base-firmware,2.3.7.0 (Paco),Firmware 2.3,bug,,infoneeded,2013-01-01T22:04:05Z,2013-05-02T09:54:18Z,"Upgraded Fonera 2n from beta3 to 2.3.7.0 Paco final. Problem: samba stopped working, access denied to Disc-A1 or Media. Error: C:\>net use R: \\192.168.0.2\Disc-A1 /user:fonero my...pass System error 5 has occurred. Access is denied. Tested on Windows XP SP3. ",mihaly.reg@… 3,1258,USB disk mounts not available after power on,fon-base-firmware,2.3.7.0 (Paco),Firmware 2.3,bug,,investigate,2013-04-02T12:19:49Z,2013-04-24T09:41:48Z,"Hi, after a power cycle (power off and on) usb disk mounts are not available. I have to disconnect usb cable, reboot fonera and reconnect usb cable to get it working again. This is quite annoying.",guandalf@… 3,1243,Wide links = no breaks Media share,fon-base-firmware,2.3.7.0 (Paco),Firmware 2.3.8.0,bug,,confirmed,2013-01-03T14:20:05Z,2013-03-13T18:43:46Z,"Upgrade from 2.3.7.0 beta3 to Paco final. File sharing was already activated in beta and worked, with disc named Disc-A1. After upgrade I have renamed Disc-A1 to 'Files' (suggestion in another ticket) And I have this behavior accessing from win xp: \\192.168.0.2\Files works fine \\192.168.0.2\Media is ok, but then \\192.168.0.2\Media\Files give this error: ...not accessible....access denied (see screen capture) ",tman 3,1257,error message from /etc/fonstated/FWallDaemon,fon-base-firmware,2.3.7.0 (Paco),Firmware 2.3.8.0,bug,,confirmed,2013-03-25T12:33:24Z,2013-04-24T08:03:08Z,"the following error messages are being printed on bootup {{{ Mar 13 14:03:16 Fonera user.info : Loading rules Mar 13 14:03:16 Fonera user.info : Loading forwarding Mar 13 14:03:16 Fonera user.info : Loading redirects Mar 13 14:03:16 Fonera user.info : Loading includes Mar 13 14:03:16 Fonera user.info : /etc/firewall.fon Mar 13 14:03:16 Fonera user.info : FWallFON Mar 13 14:03:16 Fonera user.info : FWallDaemon Mar 13 14:03:16 Fonera user.info : iptables v1.4.0: invalid port/service `uci' specified Mar 13 14:03:16 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:16 Fonera user.info : iptables v1.4.0: invalid port/service `get' specified Mar 13 14:03:16 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:16 Fonera user.info : iptables v1.4.0: invalid port/service `services.openvpn.tcp_port' specified Mar 13 14:03:16 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : iptables v1.4.0: invalid port/service `uci' specified Mar 13 14:03:17 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : iptables v1.4.0: invalid port/service `get' specified Mar 13 14:03:17 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : iptables v1.4.0: invalid port/service `services.openvpn.udp_port' specified Mar 13 14:03:17 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : killall: chilli: no process killed Mar 13 14:03:17 Fonera user.info : /etc/firewall.user }}} bootup logread output follows: {{{ BusyBox v1.11.1 (2013-03-13 14:55:49 CET) built-in shell (ash) Enter 'help' for a list of built-in commands. ------ Fonera 2.0n Firmware (SVN trunk) ----------- * Based on OpenWrt - http://openwrt.org * Powered by FON - http://www.fon.com ---------------------------------------------------- root@Fonera:~# logread |grep -v transmission && logread -f |grep -v transmission Mar 13 14:03:07 Fonera user.info kernel: [42949385.440000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Mar 13 14:03:07 Fonera user.info kernel: [42949385.640000] usbcore: registered new interface driver usbserial Mar 13 14:03:07 Fonera user.info kernel: [42949385.650000] drivers/usb/serial/usb-serial.c: USB Serial Driver core Mar 13 14:03:08 Fonera user.info kernel: [42949385.900000] Linux video capture interface: v2.00 Mar 13 14:03:08 Fonera user.info kernel: [42949386.030000] hso: drivers/usb/serial/hso.c: 1.6-Option Option Wireless Mar 13 14:03:08 Fonera user.info kernel: [42949386.040000] usbcore: registered new interface driver hso Mar 13 14:03:08 Fonera user.info kernel: [42949386.120000] drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) Mar 13 14:03:08 Fonera user.info kernel: [42949386.130000] usbcore: registered new interface driver option Mar 13 14:03:08 Fonera user.info kernel: [42949386.140000] drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2 Mar 13 14:03:08 Fonera user.info kernel: [42949386.200000] drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (1 port) Mar 13 14:03:08 Fonera user.info kernel: [42949386.210000] drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (3 port) Mar 13 14:03:08 Fonera user.info kernel: [42949386.220000] usbcore: registered new interface driver sierra Mar 13 14:03:08 Fonera user.info kernel: [42949386.230000] drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.0.6 Mar 13 14:03:08 Fonera user.info : iptables: No chain/target/match by that name Mar 13 14:03:08 Fonera user.info : iptables: No chain/target/match by that name Mar 13 14:03:08 Fonera user.info : iptables: No chain/target/match by that name Mar 13 14:03:08 Fonera user.info : iptables: No chain/target/match by that name Mar 13 14:03:08 Fonera user.info : iptables: No chain/target/match by that name Mar 13 14:03:08 Fonera user.info : iptables: No chain/target/match by that name Mar 13 14:03:08 Fonera user.warn kernel: [42949386.390000] fuse init (API version 7.8) Mar 13 14:03:08 Fonera user.info kernel: [42949386.470000] usbcore: registered new interface driver uvcvideo Mar 13 14:03:08 Fonera user.info kernel: [42949386.480000] USB Video Class driver (SVN r215) Mar 13 14:03:08 Fonera user.info : switch reg write offset=48, value=1001 Mar 13 14:03:10 Fonera user.info : ifconfig: SIOCGIFFLAGS: No such device Mar 13 14:03:10 Fonera user.info : ifconfig: SIOCGIFFLAGS: No such device Mar 13 14:03:10 Fonera user.info : killall: ap_client: no process killed Mar 13 14:03:10 Fonera user.warn kernel: [42949388.190000] setting region code 1 Mar 13 14:03:10 Fonera user.warn kernel: [42949388.200000] setting region code 7 Mar 13 14:03:10 Fonera user.warn kernel: [42949388.200000] RA_WIFI using 2 SSIDs Mar 13 14:03:10 Fonera user.warn kernel: [42949388.210000] geo beacon private:0 public:0 Mar 13 14:03:10 Fonera user.warn kernel: [42949388.260000] MAC: 00:18:84:88:92:64 Mar 13 14:03:13 Fonera user.warn kernel: [42949390.970000] 0x1300 = 00064320 Mar 13 14:03:14 Fonera user.info kernel: [42949392.030000] device ra0 entered promiscuous mode Mar 13 14:03:14 Fonera user.info kernel: [42949392.040000] br-lan: port 2(ra0) entering learning state Mar 13 14:03:14 Fonera user.info kernel: [42949392.050000] br-lan: topology change detected, propagating Mar 13 14:03:14 Fonera user.info kernel: [42949392.060000] br-lan: port 2(ra0) entering forwarding state Mar 13 14:03:14 Fonera user.info : Loading defaults Mar 13 14:03:14 Fonera user.info : Loading synflood protection Mar 13 14:03:14 Fonera user.info : Adding custom chains Mar 13 14:03:15 Fonera user.info : Loading zones Mar 13 14:03:15 Fonera user.info : iptables: Chain already exists Mar 13 14:03:15 Fonera user.info : iptables: Chain already exists Mar 13 14:03:15 Fonera user.info : iptables: Chain already exists Mar 13 14:03:16 Fonera user.info : iptables: Chain already exists Mar 13 14:03:16 Fonera user.info : iptables: Chain already exists Mar 13 14:03:16 Fonera user.info : iptables: Chain already exists Mar 13 14:03:16 Fonera user.info : Loading rules Mar 13 14:03:16 Fonera user.info : Loading forwarding Mar 13 14:03:16 Fonera user.info : Loading redirects Mar 13 14:03:16 Fonera user.info : Loading includes Mar 13 14:03:16 Fonera user.info : /etc/firewall.fon Mar 13 14:03:16 Fonera user.info : FWallFON Mar 13 14:03:16 Fonera user.info : FWallDaemon Mar 13 14:03:16 Fonera user.info : iptables v1.4.0: invalid port/service `uci' specified Mar 13 14:03:16 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:16 Fonera user.info : iptables v1.4.0: invalid port/service `get' specified Mar 13 14:03:16 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:16 Fonera user.info : iptables v1.4.0: invalid port/service `services.openvpn.tcp_port' specified Mar 13 14:03:16 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : iptables v1.4.0: invalid port/service `uci' specified Mar 13 14:03:17 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : iptables v1.4.0: invalid port/service `get' specified Mar 13 14:03:17 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : iptables v1.4.0: invalid port/service `services.openvpn.udp_port' specified Mar 13 14:03:17 Fonera user.info : Try `iptables -h' or 'iptables --help' for more information. Mar 13 14:03:17 Fonera user.info : killall: chilli: no process killed Mar 13 14:03:17 Fonera user.info : /etc/firewall.user Mar 13 14:03:17 Fonera user.notice root: adding tun-ovpn to firewall zone vpn Mar 13 14:03:18 Fonera user.notice root: adding br-lan to firewall zone lan Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: Found user 'nobody' (UID 65534) and group 'nogroup' (GID 65534). Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: Successfully dropped root privileges. Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: avahi-daemon 0.6.25 starting up. Mar 13 14:03:18 Fonera daemon.warn avahi-daemon[1430]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns! Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: No service file found in /tmp/mdns/. Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: Joining mDNS multicast group on interface br-lan.IPv4 with address 10.0.0.98. Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: New relevant interface br-lan.IPv4 for mDNS. Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: Network interface enumeration completed. Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: Registering new address record for 10.0.0.98 on br-lan.IPv4. Mar 13 14:03:18 Fonera daemon.info avahi-daemon[1430]: Registering HINFO record with values 'MIPS'/'LINUX'. Mar 13 14:03:19 Fonera daemon.info avahi-daemon[1430]: Server startup complete. Host name is Fonera.local. Local service cookie is 1743786757. Mar 13 14:03:19 Fonera user.notice root: setting up led : powerg Mar 13 14:03:19 Fonera user.notice root: setting up led : wifi Mar 13 14:03:20 Fonera user.crit fonstated: fonstated - v2.0 Mar 13 14:03:20 Fonera user.crit fonstated: loaded fontimer for ""/bin/thinclient dummy"" period=17280 Mar 13 14:03:20 Fonera user.crit fonstated: loaded fontimer for ""/etc/fonstated/RestartNtpclient"" period=17280 Mar 13 14:03:20 Fonera user.crit fonstated: loaded fontimer for ""/etc/init.d/fonsmcd"" period=12 Mar 13 14:03:20 Fonera user.crit fonstated: loaded fontimer for ""/etc/fonstated/StartHttpd"" period=2150 Mar 13 14:03:20 Fonera user.crit fonstated: starting chillispot fonstate plugin Mar 13 14:03:20 Fonera user.crit fs: Failed to connect to socket (/tmp/fonstated.sock): No such file or directory Mar 13 14:03:20 Fonera user.crit fonstated: added fontimer libcallback period=60 Mar 13 14:03:20 Fonera user.crit fonstated: added fontimer libcallback period=17280 Mar 13 14:03:20 Fonera user.crit fonstated: added fonevent hotspot_decount -> libcallback 1 Mar 13 14:03:20 Fonera user.crit fonstated: added fonevent hotspot_inccount -> libcallback 1 Mar 13 14:03:20 Fonera user.crit fonstated: added fonevent hotspot_resetcount -> libcallback 1 Mar 13 14:03:20 Fonera user.crit fonstated: added fonevent hotspot_wdt_start -> libcallback 1 Mar 13 14:03:20 Fonera user.crit fonstated: added fonevent hotspot_wdt_stop -> libcallback 1 Mar 13 14:03:20 Fonera user.crit fonstated: enqueue --> UMTS Mar 13 14:03:20 Fonera user.crit fonstated: enqueue --> SetupHosts Mar 13 14:03:20 Fonera user.crit fonstated: enqueue --> BootServices Mar 13 14:03:20 Fonera user.crit fonstated: enqueue --> FWallDaemon Mar 13 14:03:20 Fonera user.crit fonstated: enqueue --> StartTorrent Mar 13 14:03:20 Fonera user.crit fonstated: running event /etc/fonstated/UMTS Mar 13 14:03:20 Fonera user.crit fonstated: finished running /etc/fonstated/UMTS Mar 13 14:03:20 Fonera user.crit fonstated: running event /etc/fonstated/SetupHosts Mar 13 14:03:20 Fonera user.crit fonstated: finished running /etc/fonstated/SetupHosts Mar 13 14:03:20 Fonera user.crit fonstated: running event /etc/fonstated/BootServices Mar 13 14:03:20 Fonera user.notice root: runnow --> /etc/fonstated/Redirect Mar 13 14:03:20 Fonera user.notice root: runnow --> /etc/fonstated/StartFonsmcd Mar 13 14:03:20 Fonera user.notice root: runnow --> /etc/fonstated/RestartMountd Mar 13 14:03:21 Fonera daemon.info fonsmcd[1640]: Sucessfully started Mar 13 14:03:21 Fonera user.notice root: runnow --> /etc/fonstated/StartHttpd Mar 13 14:03:21 Fonera user.crit mountd[1647]: Starting OpenWrt (auto)mountd V1 Mar 13 14:03:21 Fonera user.crit mountd[1647]: trying to mount /tmp/run/mountd/ as the autofs root Mar 13 14:03:21 Fonera user.crit fonstated: finished running /etc/fonstated/BootServices Mar 13 14:03:21 Fonera user.crit fonstated: running event /etc/fonstated/FWallDaemon Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: started, version 2.45 cachesize 150 Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: compile time options: IPv6 GNU-getopt ISC-leasefile no-DBus no-I18N TFTP Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: DHCP, IP range 10.0.0.100 -- 10.0.0.250, lease time 12h Mar 13 14:03:22 Fonera user.info syslog: whitelist file: /etc/fon/whitelist.dnsmasq Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: using local addresses only for domain lan Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: reading /tmp/resolv.conf.auto Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: using nameserver 10.0.0.1#53 Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: using local addresses only for domain lan Mar 13 14:03:22 Fonera daemon.info dnsmasq[1695]: read /etc/hosts - 2 addresses Mar 13 14:03:22 Fonera daemon.err dnsmasq[1695]: failed to read /etc/ethers:No such file or directory Mar 13 14:03:22 Fonera authpriv.info dropbear[1681]: Not backgrounding Mar 13 14:03:22 Fonera user.crit mountd[1647]: new mount : FreeAgent -> sda1 (EXT3) Mar 13 14:03:22 Fonera user.crit mountd[1647]: mounting /tmp/run/mountd/sda1 Mar 13 14:03:22 Fonera user.crit mountd[1712]: mount -t ext3 -o rw,noatime,defaults /dev/sda1 /tmp/run/mountd/sda1 Mar 13 14:03:22 Fonera daemon.info avahi-daemon[1430]: Got SIGHUP, reloading. Mar 13 14:03:22 Fonera daemon.info avahi-daemon[1430]: Loading service file /tmp/mdns//ftp.service. Mar 13 14:03:22 Fonera daemon.info avahi-daemon[1430]: Loading service file /tmp/mdns//ssh.service. Mar 13 14:03:22 Fonera daemon.info avahi-daemon[1430]: Got SIGHUP, reloading. Mar 13 14:03:22 Fonera user.emerg syslog: starting onlined Mar 13 14:03:22 Fonera user.emerg syslog: new online state Online Mar 13 14:03:22 Fonera daemon.info avahi-daemon[1430]: Got SIGHUP, reloading. Mar 13 14:03:22 Fonera daemon.info avahi-daemon[1430]: Loading service file /tmp/mdns//smb.service. Mar 13 14:03:23 Fonera daemon.info avahi-daemon[1430]: Service ""Fonera2.0 SSH"" (/tmp/mdns//ssh.service) successfully established. Mar 13 14:03:23 Fonera daemon.info avahi-daemon[1430]: Service ""Fonera2.0 FTP Server"" (/tmp/mdns//ftp.service) successfully established. Mar 13 14:03:23 Fonera user.notice root: runnow --> /etc/fonstated/SetupDlmd Mar 13 14:03:23 Fonera daemon.info avahi-daemon[1430]: Service ""LaFonera"" (/tmp/mdns//smb.service) successfully established. Mar 13 14:03:23 Fonera user.info kernel: [42949401.820000] kjournald starting. Commit interval 5 seconds Mar 13 14:03:23 Fonera user.info kernel: [42949401.830000] EXT3 FS on sda1, internal journal Mar 13 14:03:23 Fonera user.info kernel: [42949401.840000] EXT3-fs: recovery complete. Mar 13 14:03:23 Fonera user.info kernel: [42949401.850000] EXT3-fs: mounted filesystem with ordered data mode. Mar 13 14:03:24 Fonera user.crit mountd[1647]: ----------> mount ret = 0 Mar 13 14:03:24 Fonera user.crit fonstated: finished running /etc/fonstated/FWallDaemon Mar 13 14:03:24 Fonera user.crit fonstated: running event /etc/fonstated/StartTorrent Mar 13 14:03:24 Fonera user.crit fonstated: finished running /etc/fonstated/StartTorrent Mar 13 14:03:24 Fonera user.crit fonstated: enqueue --> Online Mar 13 14:03:24 Fonera user.crit fonstated: running event /etc/fonstated/Online Mar 13 14:03:24 Fonera daemon.notice openvpn(openvpn)[1748]: OpenVPN 2.2.2 mipsel-linux [SSL] [LZO2] built on Mar 13 2013 Mar 13 14:03:24 Fonera daemon.warn openvpn(openvpn)[1748]: NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Mar 13 14:03:24 Fonera user.notice root: runnow --> /etc/fonstated/HotspotStart Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: Diffie-Hellman initialized with 1024 bit key Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: Socket Buffers: R=[109568->131072] S=[109568->131072] Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: TUN/TAP device tun-ovpn opened Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: TUN/TAP TX queue length set to 100 Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: /sbin/ifconfig tun-ovpn 10.8.0.1 netmask 255.255.255.0 mtu 1500 broadcast 10.8.0.255 Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: UDPv4 link local (bound): [undef]:1194 Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: UDPv4 link remote: [undef] Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: MULTI: multi_init called, r=256 v=256 Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: IFCONFIG POOL: base=10.8.0.2 size=126 Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: IFCONFIG POOL LIST Mar 13 14:03:25 Fonera daemon.notice openvpn(openvpn)[1748]: Initialization Sequence Completed Mar 13 14:03:25 Fonera authpriv.info dropbear[1776]: Child connection from Mar 13 14:03:26 Fonera authpriv.notice dropbear[1776]: pubkey auth succeeded for 'root' with Mar 13 14:03:27 Fonera local6.info chillispot[1881]: tun.c: 664: 2 (No such file or directory) TX queue length set to 100 Mar 13 14:03:27 Fonera local6.info chillispot[1881]: ChilliSpot 1.0-coova.4. Copyright 2002-2005 Mondru AB. Licensed under GPL. Copyright 2006 Coova Technologies Ltd. Licensed under GPL. See http://www.chillispot.org for credits. Mar 13 14:03:27 Fonera user.notice root: adding tun0 to firewall zone hotspot Mar 13 14:03:27 Fonera user.notice root: runnow --> /etc/fonstated/RestartNtpclient Mar 13 14:03:28 Fonera user.crit fonstated: finished running /etc/fonstated/Online Mar 13 14:03:28 Fonera user.crit fonstated: enqueue --> hotspot_wdt_start Mar 13 14:03:28 Fonera user.crit fonstated: running fast event hotspot_wdt_start Mar 13 14:03:28 Fonera user.crit fonstated: starting chilli wdt Mar 13 14:03:29 Fonera user.notice root: starting ntpclient Mar 25 12:08:04 Fonera user.crit mountd[1754]: starting torrent sda1 Mar 25 12:08:04 Fonera user.crit fonstated: enqueue --> SetupDlmd Mar 25 12:08:04 Fonera user.crit fonstated: running event /etc/fonstated/SetupDlmd Mar 25 12:08:05 Fonera user.crit fonstated: finished running /etc/fonstated/SetupDlmd Mar 25 12:08:05 Fonera local6.info chillispot[1881]: options.c: 782: Rereading configuration file and doing DNS lookup Mar 25 12:08:05 Fonera user.info kernel: [42949409.020000] Adding 129528k swap on /tmp/mounts/FreeAgent//FoneraApps/torrent.2.3.8.0.swp. Priority:-1 extents:34 across:130716k }}} the same error message can be produced by directly calling FWallDaemon: {{{ root@Fonera:~# /etc/fonstated/FWallDaemon iptables v1.4.0: invalid port/service `uci' specified Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.0: invalid port/service `get' specified Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.0: invalid port/service `services.openvpn.tcp_port' specified Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.0: invalid port/service `uci' specified Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.0: invalid port/service `get' specified Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.0: invalid port/service `services.openvpn.udp_port' specified Try `iptables -h' or 'iptables --help' for more information. root@Fonera:~# }}} ",Thomas Horner 4,385,"FTP does not support ""long file names""",fon-base-firmware,Other,Firmware 2.3,bug,,investigate,2009-09-25T21:24:40Z,2012-12-19T12:15:06Z,"I notice I can't put any files longer than 31 chars on the Fonera FTP server? an example of the ""logread"" logging: http://pastebin.com/m731eec6b but on my Ubuntu under details it says ""invalid filename"" as error... when I make it shorter like drop "".hdtv.Xvid-fqm"" then it works is this a limitation of Vfat or the ftp server?",steven@… 4,496,"If firmware is compiled without Twitter support, link is still there",fon-plugins,2.3.7.0 rc2,Firmware 2.3,bug,iurgi@…,investigate,2009-12-12T20:45:17Z,2012-12-19T15:18:00Z,"I have compiled a firmware without Twitter, Facebook, Flickr and so on. But the links for them are still available in LuCI.",carsten.schuette@… 4,625,transmission TCP port and iptables update,fon-plugin-transmission,2.3.7.0 rc2,Firmware 2.3,bug,,confirm,2010-04-08T13:33:40Z,2012-12-20T08:25:38Z,"When transmission TCP listen port is changed, iptables rules are not updated. So if transmission's port is not the default one it is blocked by iptables, if not updated manually (i.e. adding rule at the end of /etc/profile).",sourstar 3,824,Mac-Passthrough feature,fon-network,N/A,,enhancement,john.crispin@…,investigate,2010-06-07T15:35:04Z,2011-12-03T02:15:24Z,"It would be great to have the mac-passthrough feature. This would enable me to use a Fonera between my Digital TV decoder and my adsl/cablemodem. Now I have to use a powerplug between my Cable modem & Decoder and a switch between my Cable modem and my Fonera At the moment other brands & firmwares allow allready mac-passthrough to avoid extra hardware & costs... Even the new wireless cablemodems come with this feature now ... only the foneras do not allow this yet. The Decoders request an ip not on the Fonera Dhcp but the WANside of the router...and get another ip range thus....",steven@… 3,845,Tucan manager on fonera,other,N/A,,enhancement,,investigate,2010-06-28T16:30:37Z,2012-01-18T06:58:53Z,"Hi, as you can see here [http://forum.fon.com/forum/viewtopic.php?f=8&t=137] I successfully installed tucan on the fonera. I've been tested it since now and I have to say that it works very fine. I'm suggesting you to support this project and maybe create a dedicated gui to make it more user-friendly. When I bought the fonera 2.0 n I was disappointed to find out that the downloader was just for premium users. Now my fonera satisfy me a little bit more, but it can do better.",bisont87 3,862,Add bandwidth history to status page,fon-network,N/A,,enhancement,,confirmed,2010-07-13T21:35:15Z,2010-07-14T08:51:53Z,"Could the status page be changed into a bandwith monitor? with a past 24 hour graph, and a daily consumption log? i think this is done with rrdtool? in tomato there is such a function though i haven't seen it in any other router this would really be a cool feature",koter84@… 3,883,Hide SSID,fon-wifi,N/A,,enhancement,john.crispin@…,investigate,2010-08-23T10:13:33Z,2013-04-18T17:36:08Z,"This is a translation of #397. I think that is a must-have the option to configure the MyPlace SSID,so it is hidden for WLAN searches. If you have the option to disable the broadcasting of the SSID, you can make your network more secure as is explained here: http://netsecurity.about.com/od/quicktip1/qt/qtwifinossid.htm So you need to know the SSID of the private network (MyPlace) to connect to it by Wi-Fi. I hope you understand what I mean, it is a little difficult to me to explain it in English.",Josemi 3,921,download and upload's bandwidth limits in download manager,fon-plugin-downloader,N/A,,enhancement,,confirmed,2010-09-16T01:46:39Z,2012-10-29T14:33:19Z,"Can you add in the download manager the bandwidth limits of download and upload as like as in transmission? It would be very useful for the manual regulation of own bandwidth.",ddomee@… 3,923,WebGUI file management interface,fon-web,Other,,enhancement,,investigate,2010-09-16T02:09:49Z,2010-09-23T23:35:38Z,"Can you add a file manager in the fonera's application? For file manager I mean something that allow to users of delete, move, copy files, or create and delete folder... etc... Everything from the gui of fonera and not through ftp or ssh",ddomee@… 3,924,More hosting site in the download manager,fon-plugin-downloader,Unknown,,enhancement,,investigate,2010-09-16T02:18:17Z,2011-12-02T23:47:33Z,"Can you add in the download manager the most known hosting website over rapidshare and megaupload? For example: www.fileserve.com http://x7.to/ http://uploading.com/ www.filefactory.com hotfile.com http://www.storage.to/ http://depositfiles.com/en/ http://filebase.to/ and maybe an option to enter manually and easy other Websites, without modifying the files over ssh, but directily from the gui",anonymous 3,925,dropbox or a folder that interface with it in fonera,fon-plugins,N/A,,enhancement,,investigate,2010-09-16T02:24:33Z,2013-03-25T18:26:03Z,"Can you create a porting of dropbox, or a similar application, or a folder that interface itself with a dropbox account, in the fonera? Thanks in advance!",ddomee@… 3,930,More info in download manager,fon-plugin-downloader,N/A,,enhancement,,investigate,2010-09-23T23:33:28Z,2011-07-06T17:07:10Z,"Hi! Can you add more info in the download manager's page? For example: * number of all files in download * number of files in downloading status * number of files in error status * number of files in completed status * number of files in canceled status * download and upload occupied bandwidth etc.. ",ddomee@… 3,1097,Remove torrent authentication,fon-plugin-transmission,2.3.7.0 beta2,,enhancement,,confirmed,2011-10-07T12:38:39Z,2011-10-10T13:24:59Z,"It would be great to have the possibility to enable/disable the authentication of the torrent web client from the fon dashboard. ",ilvalle@… 3,1120,Add AirPrint support,fon-plugin-printer,N/A,,enhancement,,confirmed,2011-11-10T11:11:26Z,2012-11-05T22:45:21Z,"It would be very useful if you can add AirPrint support for a USB printer attached to the Fonera. Instructions to do so for linux can be found with google searching +enable +airprint +linux An example for archlinux arm is here: http://archlinuxarm.org/support/guides/applications/cups-apple-airprint ",anonymous 3,1147,Support for Google Cloud Print,fon-plugin-printer,N/A,,enhancement,,confirmed,2012-02-05T09:32:17Z,2012-02-06T10:20:04Z,"Hi to all, is it possible including the support to Google Cloud Print on the next firmware? It would be great!! :-)",anonymous 3,1154,No port triggering in fonera,fon-network,N/A,,enhancement,,infoneeded,2012-02-27T21:16:11Z,2012-02-28T08:18:40Z,"Can't find port triggering feature in fonera. I't needen for some games and video streaming services. See wikipedia for a description: +++++++++++ http://en.wikipedia.org/wiki/Port_triggering Port triggering is a way to automate port forwarding in which outbound traffic on predetermined ports ('triggering ports') causes inbound traffic to specific incoming ports to be dynamically forwarded to the initiating host, while the outbound ports are in use. This allows computers behind a NAT-enabled router on a local network to provide services that would normally require the computer to have a fixed address on the local network. +++++++++++ Nowadays any router have this feature.",mihaly.reg@… 3,1195,DynDNS behind NAT doesn't work,fon-plugin-ddns,N/A,,enhancement,,confirmed,2012-07-01T04:41:10Z,2013-01-18T01:04:37Z,"I was wondering if besides the 2 options of ""IP Address to Send"": -let provider detect -use fonera internet ip (which is the ip the fonera gets on it's wan port I assume) if there is an option to get the output from a website like in the ddns-scripts package for openwrt e.g. (option ip_url ""http://automation.whatismyip.com/n09230945.asp"") ",michael.nicolai@… 3,1227,The Fon access portal should appear on the LAN connections.,other,N/A,,enhancement,,investigate,2012-10-10T13:13:45Z,2013-02-20T23:49:18Z,"The Fon access portal only appears on the Fon public signal and there's no way to make it appear on the private or the LAN connections. You can block access from the private signal and LAN ports to the WAN (internet) side, but that will not show the access portal. As I tryed to integrate fonera 2.0n (FON2303a) into a exsiting hotel network I would like that feature to be @ the next release :-).",Andreas@… 3,10,Bluetooth,unknown,N/A,,enhancement,iurgi@…,confirmed,2008-12-04T13:55:13Z,2012-07-02T05:52:41Z,Would be interesting to have a working bluetooth stack/bluez available for the Fonera 2,steven@… 3,35,Hard Disk formatting / partitioner / checkdisk tool app,fon-base-firmware,N/A,,enhancement,iurgi@…,confirmed,2009-01-02T14:18:10Z,2013-03-25T14:54:22Z,"Since it is recomended to use ext2/ext3 formated disks with Fonera 2.0, an app capable of formatting usb discs with this format would be nice. Otherwise, linux based computer and skills are required wich is not always available for the average non-expert user. ",anonymous 3,203,audiocli: manual soundcard selection,fon-plugin-music,,,enhancement,iurgi@…,confirmed,2009-02-09T15:42:21Z,2010-05-31T08:32:56Z,my webcam is detected as a soundcard because of the integrated microphone. it would be nice select the output soundcard to get music with webcam and soudncard equiped together on boot.,kazwo 3,236,Webcam plugin public page,fon-plugin-webcam,N/A,,enhancement,iurgi@…,confirmed,2009-03-09T23:36:04Z,2012-12-19T09:24:37Z,"Now, when you want to see the images captured by your webcam attached to LF2 you must enter the admin password. This disables you to share your webcam's stream with other people so a public webcam page with no authenticatin required or a invitation to see system would be fantastic in order to share your fonera live strem. ",decodecoding@… 3,248,UMTS/3G manual or scheduled dialing,fon-network-3g,N/A,,enhancement,iurgi@…,confirmed,2009-04-28T16:09:22Z,2012-12-24T10:53:43Z,"most UMTS contracts are not flat, they are usually bounded on time or on data transferred. at the moment the fon2 keeps the connection always-on and this may bring to very high bills! an easy solution would be to enable manual umts connection clickin on a button in the webui; a more advanced option would be to configure the provider plan (by time or by traffic) more throughly (some like: stay always-on from 5pm to 9am and switch to manual connection otherwise). thanks!",barbato@… 3,251,Support 3G dongle: Option ICON 401,fon-network-3g,N/A,,enhancement,john.crispin@…,investigate,2009-04-29T18:51:41Z,2012-12-19T09:40:18Z,"I want to use Fonera 2 as a mobile/personal hotspot, so only use it with a 3G dongle. But when I plug in my dongle, nothing happens; no USB led light and a 3G cross on the dashboard. Here's my setup: - Fonera 2.0 (2.2.5.0 ""flipper"" firmware)[[BR]] - 3G: KPN Mobile (The Netherlands)[[BR]] - Dongle: Option ICON 401[[BR]] http://www.option.com/en/products/products/usb-modems/icon401/ Any clue or better experience?",fon@… 3,257,Support 3G dongle: Vodafone K3520,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-05-04T07:07:33Z,2012-12-19T11:07:36Z,"I purchased the Huawei K3520 umts dongle (this modem is a cosmetic change of Huawei E169 (http://www.myceloteh.com/?p=336)) for the fonera 2.0. I'm not able to get the vodafone umts dongle working. At first i tried to connect the dongle to the usb port without a hub, the fonera did not even see it was there, after that i attached a usb hub with external power supply. Now the fonera does see the dongle but it keeps on telling that it is dialing in, but it never succeeds. Also the led doesnt turn to blue as it does when you connect it to the pc (it keeps blinking green). When I connect directly to my laptop, it dials in without a problem. I searched all over the net for a solution, but i could not find anything, i would realllly appreciate it when you could help me out with this as i dont have an alternatieve for the dongle. Dongle: http://www.vodafone.nl/shop/handset/Adviestool/cat10760001/USB-stick+Vast/sku10760024 Thanks in advance! Frank ",frank.kroondijk@… 3,264,Active connections in realtime,fon-web,Unknown,,enhancement,iurgi@…,investigate,2009-05-10T18:38:43Z,2012-12-19T10:06:48Z,"Can you enter the following features (which were present in the patch freewlan):[[BR]] 1) '''Enhanced Status page''' - Tells you in realtime who is connected on the Private & Public networks[[BR]] 2) '''MAC-Blocking''' - Disallow certain users on your hotspot [[Image(http://www.webalice.it/giuseppeg88/fon/active_connections.jpg)]] thanks!",giuseppeg88 3,280,Video upload for Facebook app,fon-plugin-facebook,N/A,,enhancement,iurgi@…,investigate,2009-05-24T17:38:14Z,2010-07-22T12:27:05Z,"I'd love to be able to also upload videos to Facebook using fonera the same as Youtube app is able to, and no only pictures. ",decodecoding@… 3,285,Support 3G dongle: Huawei E172,fon-network-3g,N/A,,enhancement,john.crispin@…,investigate,2009-06-02T21:25:11Z,2012-12-20T10:39:07Z,"here is the Log Jun 1 22:04:45 Fonera user.crit syslog: enqueue --> HotspotStop Jun 1 22:04:45 Fonera user.crit syslog: running event /etc/fonstated/HotspotStop Jun 1 22:04:45 Fonera user.crit syslog: finished running /etc/fonstated/HotspotStop Jun 1 22:04:49 Fonera daemon.notice pppd[1886]: pppd 2.4.3 started by root, uid 0 Jun 1 22:04:50 Fonera local2.info chat[1888]: abort on (NO CARRIER) Jun 1 22:04:50 Fonera local2.info chat[1888]: abort on (NO DIALTONE) Jun 1 22:04:50 Fonera local2.info chat[1888]: abort on (ERROR) Jun 1 22:04:50 Fonera local2.info chat[1888]: abort on (NO ANSWER) Jun 1 22:04:50 Fonera local2.info chat[1888]: abort on (BUSY) Jun 1 22:04:50 Fonera local2.info chat[1888]: send (+++atz^M) Jun 1 22:04:50 Fonera local2.info chat[1888]: expect (OK) Jun 1 22:04:50 Fonera local2.info chat[1888]: ^M Jun 1 22:04:50 Fonera local2.info chat[1888]: OK Jun 1 22:04:50 Fonera local2.info chat[1888]: -- got it Jun 1 22:04:50 Fonera local2.info chat[1888]: send (ATE0V1^M) Jun 1 22:04:50 Fonera local2.info chat[1888]: expect (OK) Jun 1 22:04:50 Fonera local2.info chat[1888]: ^M Jun 1 22:04:50 Fonera local2.info chat[1888]: ATE0V1^M^M Jun 1 22:04:50 Fonera local2.info chat[1888]: OK Jun 1 22:04:50 Fonera local2.info chat[1888]: -- got it Jun 1 22:04:50 Fonera local2.info chat[1888]: send (AT+CGDCONT=1,""IP"",""slsfr""^M) Jun 1 22:04:50 Fonera local2.info chat[1888]: expect (OK) Jun 1 22:04:50 Fonera local2.info chat[1888]: ^M Jun 1 22:04:50 Fonera local2.info chat[1888]: ^M Jun 1 22:04:50 Fonera local2.info chat[1888]: OK Jun 1 22:04:50 Fonera local2.info chat[1888]: -- got it Jun 1 22:04:50 Fonera local2.info chat[1888]: send (ATD*99***1#^M) Jun 1 22:04:50 Fonera local2.info chat[1888]: expect (CONNECT) Jun 1 22:04:50 Fonera local2.info chat[1888]: ^M Jun 1 22:04:51 Fonera local2.info chat[1888]: ^M Jun 1 22:04:51 Fonera local2.info chat[1888]: CONNECT Jun 1 22:04:51 Fonera local2.info chat[1888]: -- got it Jun 1 22:04:51 Fonera local2.info chat[1888]: send (^M) Jun 1 22:04:51 Fonera daemon.info pppd[1886]: Serial connection established. Jun 1 22:04:51 Fonera daemon.info pppd[1886]: Using interface ppp0 Jun 1 22:04:51 Fonera daemon.notice pppd[1886]: Connect: ppp0 <--> /dev/ttyUSB0 Jun 1 22:04:52 Fonera daemon.info pppd[1886]: CHAP authentication succeeded Jun 1 22:04:52 Fonera daemon.notice pppd[1886]: CHAP authentication succeeded Jun 1 22:04:52 Fonera user.err kernel: usb 1-1: clear tt 1 (9042) error -71 Jun 1 22:04:54 Fonera authpriv.info dropbear[1892]: Child connection from 192.168.10.209:52885 Jun 1 22:04:58 Fonera daemon.info pppd[1886]: No response to 5 echo-requests Jun 1 22:04:58 Fonera daemon.notice pppd[1886]: Serial link appears to be disconnected. Jun 1 22:05:00 Fonera daemon.notice pppd[1886]: Modem hangup Jun 1 22:05:00 Fonera daemon.notice pppd[1886]: Connection terminated. 3G won't connect APN etc are correct .. don't understand why :'( any idear ?",depanet@… 3,289,Usenet support,fon-plugins,N/A,,enhancement,iurgi@…,investigate,2009-06-04T14:59:35Z,2012-12-19T10:39:50Z,"It would be verry handy if a usenet client can be included. I use usenet all the time, but now my PC have to stay on forever to download everything. Offcourse the Fonera 2.0 isn't fast enough to unrar or unpar everything. But it would be nice if it could donwload just the .rar from an .nzb.",wt.maes@… 3,321,using iphone tethering failed,fon-network-3g,Unknown,,enhancement,iurgi@…,investigate,2009-07-12T23:53:50Z,2012-12-19T11:05:35Z,I tried using my iphone as a 3G modem but it failed. The tethering is activated on the iphone and the iphone acts as it is connected to someting but the actual sharing of the connection doesn't start. It would be really cool if this could be supported.,bigfatbball2@… 3,324,Support 3G dongle: Ice.net C-motech D-50,fon-network-3g,N/A,,enhancement,,investigate,2009-07-15T15:52:59Z,2012-12-19T11:07:16Z,"Hi, I'm having trouble using a C-motech D-50 on the Fonera 2.0. It won't recognize the 3G USB Stick. Also the Fonera 2.0 knows the settings for the Swedish Ice.net provider, but it won't save the setting, probably because Ice.net doesn't use a APN. But if I put in the settings manually, it still won't recognize my USB 3G stick. Even with a USB hub attached! Different sticks are recognized, like the NL T-Mobile stick. ",paulvdwal1@… 3,361,Support 3G dongle: HUAWEI E1550,fon-network-3g,N/A,,enhancement,,investigate,2009-08-25T18:00:42Z,2012-12-19T11:39:01Z,"My 3G Modem HUAWEI E1550 is not recognized by the La Fonera 2 Firmware Version: 2.2.5.0 The Modem ist from COMVIQ and is run as a prepaid solution in Sweden. When plugged into the La Fonera the Fonera Software says that there is no UMTS / 3G device connected. What is the problem? Do I have to use a USB hub with external energy supply for this modem? Is a newer version of the firmware available that will help me to get the modem running? ",me@… 3,364,Support 3G dongle: Novatel Ovation MC950D,fon-network-3g,N/A,,enhancement,john.crispin@…,investigate,2009-09-02T18:38:33Z,2012-12-19T11:57:39Z,"'''Spanish Vodafone''' 3G modem '''Novatel Ovation MC950D''' doesn't work. Not sure but seems that it doesn't be detected by F2. I have tryed rebooting F2 with modem connected, but nothing. More information: {{{ root@Fonera:~# cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 3 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.26.2 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:00.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms }}} Please to try any idea, test or whatever. I am '''using R.2.2.6.0 RC5 Developer'''.",Jorge 3,373,Support 3G dongle: Longcheer WM66 USB HSDPA Modem,fon-base-firmware,N/A,,enhancement,iurgi@…,investigate,2009-09-21T12:58:14Z,2012-12-19T12:09:09Z,"I'm trying to get a MasMovil rebranded Longcheer WM66 USB HSDPA Modem working with Fonera 2.0 running 20090713_FON2202_2.2.6.0_rc5_DEV When the modem is inserted into the USB port, the web GUI sez ""There is no UMTS/3G device attached"" Repeating the proceduce while logged into the Fonera via ssh, shows no activity via the logread -f command in real time either. cat /proc/bus/usb/devices yields the following with the modem plugged in. T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 3 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.26.2 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:00.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms ",fon.21c@… 3,374,Support 3G dongle: Huawei K3715,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-09-21T21:08:44Z,2012-12-19T12:12:04Z,"Here are the results from commands on the Wiki page. This is for a Huawei K3715, Vodafone-branded. This 3G USB dongle has been tested with Swedish operator Halebop and German Vodafone. cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 3 B: Alloc= 1/800 us ( 0%), #Int= 1, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.26.2 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:00.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1001 Rev= 0.00 S: Manufacturer=HUAWEI Technology S: Product=HUAWEI Mobile C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms ---------------- dmesg Linux version 2.6.26.2 (blogic@blap4) (gcc version 4.1.2) #10 Tue Apr 21 14:12:05 CEST 2009 CPU revision is: 00019064 (MIPS 4KEc) Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Entering add_active_range(0, 0, 8192) 0 entries of 256 used Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0 -> 8192 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 8192 On node 0 totalpages: 8192 Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8128 pages, LIFO batch:0 Movable zone: 0 pages used for memmap Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/preinit Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29784k/32768k available (1889k kernel code, 2984k reserved, 317k data, 128k init, 0k highmem) SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Calibrating delay loop... 183.50 BogoMIPS (lpj=917504) Mount-cache hash table entries: 512 net_namespace: 484 bytes NET: Registered protocol family 16 Radio config found at offset 0xf8(0x1f8) AR531x PCI init... done PCI: fixing up device 0,3,0 PCI: Failed to allocate mem resource #1:4000000@84000000 for 0000:00:03.0 Switched to high resolution mode on CPU 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 ar531x: Registering GPIODEV device gpio_proc: module loaded and /proc/gpio/ created squashfs: version 3.0 (2006/03/15) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 58 io scheduler noop registered io scheduler deadline registered (default) gpiodev: gpio device registered with major 254 gpiodev: gpio platform device registered with access mask FFFFFFFF Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A eth0: Atheros AR231x: 00:18:84:d0:a5:a0, irq 4 ar2313_eth_mii: probed eth0: Marvell 88E6060 PHY driver attached. eth0: attached PHY driver [Marvell 88E6060] (mii_bus:phy_addr=0:1f) cmdlinepart partition parsing not available Searching for RedBoot partition table in spiflash at offset 0x7d0000 Searching for RedBoot partition table in spiflash at offset 0x7e0000 8 RedBoot partitions found on MTD device spiflash Creating 8 MTD partitions on ""spiflash"": 0x00000000-0x00030000 : ""RedBoot"" 0x00030000-0x00040000 : ""loader"" 0x00040000-0x00660000 : ""image"" 0x000f2e84-0x00660000 : ""rootfs"" mtd: partition ""rootfs"" doesn't start on an erase block boundary -- force read-only mtd: partition ""rootfs"" set to be root filesystem mtd: partition ""rootfs_data"" created automatically, ofs=4A0000, len=1C0000 0x004a0000-0x00660000 : ""rootfs_data"" 0x00660000-0x007a0000 : ""image2"" 0x007e0000-0x007ef000 : ""FIS directory"" 0x007ef000-0x007f0000 : ""RedBoot config"" 0x007f0000-0x00800000 : ""boardconfig"" Registered led device: gpio0 Registered led device: gpio1 Registered led device: wlan Registered led device: gpio3 Registered led device: gpio4 Registered led device: gpio7 nf_conntrack version 0.5.0 (1024 buckets, 4096 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP vegas registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 128k freed Please be patient, while OpenWrt loads ... Algorithmics/MIPS FPU Emulator v1.5 mini_fo: using base directory: / mini_fo: using storage directory: /jffs SCSI subsystem initialized device eth0.0 entered promiscuous mode device eth0 entered promiscuous mode br-lan: port 1(eth0.0) entering learning state br-lan: topology change detected, propagating br-lan: port 1(eth0.0) entering forwarding state usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PPP generic driver version 2.4.2 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky IPP2P v0.8.1_rc1 loading ipt_time loading Driver 'sd' needs updating - please use bus_type methods wlan: trunk ath_hal: module license 'Proprietary' taints kernel. ath_hal: 2008-10-02 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC, TX_DESC_SWAP, DFS, XR) ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk) ath_rate_minstrel: look around rate set to 10% ath_rate_minstrel: EWMA rolloff level set to 75% ath_rate_minstrel: max segment size in the mrr set to 6000 us wlan: mac acl policy registered ath_ahb: trunk Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP ath_ahb: wifi0: Atheros 2315 WiSoC: mem=0xb0000000, irq=3 PCI: Enabling device 0000:00:00.1 (0000 -> 0002) ehci_hcd 0000:00:00.1: EHCI Host Controller ehci_hcd 0000:00:00.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:00.1: irq 5, io mem 0x80c21000 ehci_hcd 0000:00:00.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected usb 1-1: new high speed USB device using ehci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice usbcore: registered new interface driver usblp usbcore: registered new interface driver usbserial usbserial: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core Initializing USB Mass Storage driver... usb 1-1: USB disconnect, address 2 scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Linux video capture interface: v2.00 usbserial: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: USB Driver for GSM modems: v0.7.2 usbserial: USB Serial support registered for Sierra USB modem usbcore: registered new interface driver sierra sierra: USB Driver for Sierra Wireless USB modems: v.1.2.9c fuse init (API version 7.9) usbcore: registered new interface driver uvcvideo USB Video Class driver (SVN r215) usb 1-1: new high speed USB device using ehci_hcd and address 3 usb 1-1: configuration #1 chosen from 1 choice usb-storage: probe of 1-1:1.0 failed with error -5 option 1-1:1.0: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 ttyusb -> 1 ttyUSB0 option 12D11001 usb-storage: probe of 1-1:1.1 failed with error -5 option 1-1:1.1: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 ttyusb -> 1 ttyUSB1 option 12D11001 usb-storage: probe of 1-1:1.2 failed with error -5 option 1-1:1.2: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 ttyusb -> 1 ttyUSB2 option 12D11001 device ath1 entered promiscuous mode br-lan: port 2(ath1) entering learning state br-lan: topology change detected, propagating br-lan: port 2(ath1) entering forwarding state scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning scsi 4:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 usb-storage: device scan complete scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning scsi 5:0:0:0: Direct-Access HUAWEI MMC Storage 2.31 PQ: 0 ANSI: 2 sd 5:0:0:0: [sda] Attached SCSI removable disk usb-storage: device scan complete usb 1-1: USB disconnect, address 3 ttyusb -> 0 ttyUSB0 option 12D11001 option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 option 1-1:1.0: device disconnected ttyusb -> 0 ttyUSB1 option 12D11001 option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 option 1-1:1.1: device disconnected ttyusb -> 0 ttyUSB2 option 12D11001 option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 option 1-1:1.2: device disconnected usb 1-1: new high speed USB device using ehci_hcd and address 4 usb 1-1: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb 1-1: USB disconnect, address 4 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb 1-1: new high speed USB device using ehci_hcd and address 5 usb 1-1: configuration #1 chosen from 1 choice usb-storage: probe of 1-1:1.0 failed with error -5 option 1-1:1.0: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 ttyusb -> 1 ttyUSB0 option 12D11001 usb-storage: probe of 1-1:1.1 failed with error -5 option 1-1:1.1: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 ttyusb -> 1 ttyUSB1 option 12D11001 usb-storage: probe of 1-1:1.2 failed with error -5 option 1-1:1.2: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 ttyusb -> 1 ttyUSB2 option 12D11001 scsi10 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning scsi 10:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 usb-storage: device scan complete scsi11 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning scsi 11:0:0:0: Direct-Access HUAWEI MMC Storage 2.31 PQ: 0 ANSI: 2 sd 11:0:0:0: [sda] Attached SCSI removable disk usb-storage: device scan complete",3guser 3,392,Fonera should check registration status at fon.com,fon-base-firmware,N/A,,enhancement,,confirmed,2009-09-27T21:38:05Z,2013-03-18T11:18:53Z,"downgraded and then went back to 2.3.0.0. Already registered router shows again register link. New registration doesn't work.",trintrax 3,398,Support 3G phone: Nokia / symbian phones,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-09-30T21:13:27Z,2012-12-19T12:24:54Z,"Hi, I would like to know if it would be possible to use usb connected phone as modem, for example i can use my nokia N95 under Linux as a usb modem, do you tihnk is possible also with La fonera 2.0 g/n ? thanks",Filippo Casamassima 3,424,Support 3G dongle: ZTE MF636,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-10-17T00:29:30Z,2012-12-19T12:20:14Z,"hello i want report and request compatiblite of the modem 3G ZTE MF636 beacouse not work in fonera 2.0. pelase help me, many people have this problem :( best regards",Gualter 3,440,Support 3G dongle: Option ICON 225,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-10-26T13:56:07Z,2012-12-19T12:42:41Z,"Hello, I've got my Fonera 2.0, running Kernel 2.3.0.1 RC1 on it, yesterday I did try to use my Icon 225 modem from Orange, but with no succeess, the USB led didn't turn on, and the modem didn't work. As I saw that Icon 225 was supported in Kernel 2.3.0.0, I would like to ask a couple of things: Is Kerenl 2.3.0.1 RC1 supporting this modem??? Do I have to do anything to use my modem on the fonera 2.0??? If you need further information, please don't hesitate to contact me. Cheers, Carlos",c.fuentesb@… 3,450,Support 3G dongle: Huawei E169G,fon-network-3g,N/A,,enhancement,,investigate,2009-10-30T15:44:41Z,2012-12-20T10:00:28Z,"Is there any way to make possible the use of this 3G dongle? Here in portugal it's a very common one, specially among the students.",alves_diogo@… 3,453,Support 3G dongle: Huaweil E15582,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-11-02T09:30:50Z,2012-12-19T12:49:13Z,Huaweil E15582 with Bouygues 3G+ sim card is not recognised by Fonera 20n(firmware 2.3.0.0). The message on dashboad is No modem UMTS/3G connected. Any idea how to make it work ? I have no background on technical things. Thanks,sulletjc@… 3,468,Support 3G dongle: Huawei E1692,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2009-11-23T13:50:29Z,2012-12-20T09:59:15Z,"TIM Huawei E1692 doesn't recognize from fonera 2.0n below some details for internet key Could you tell me some tips to recognize internet key for fonera 2.0n? thanks in advance -andrea root@Fonera:~# cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.21 dwc_otg_hcd S: Product=DWC OTG Controller S: SerialNumber=lm0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms",andrea.franco@… 3,524,ipv6 support,fon-network,N/A,,enhancement,john.crispin@…,investigate,2009-12-21T11:16:19Z,2012-12-11T17:38:14Z,"I like to use aiccu with my fonera 2.0n but I need a kernel that support the ipv6 module! Now with the 2.3.5-rc2 I got: {{{ Fonera:~/run/mountd/sda1/opk/lib# insmod modules/2.6.21/ipv6.ko insmod: cannot insert 'modules/2.6.21/ipv6.ko': unknown symbol in module (-1): No such file or directory }}} {{{ Fonera:~/run/mountd/sda1/opk/lib# dmesg [...] ipv6: Unknown symbol __ipv6_addr_type ipv6: Unknown symbol fib_rules_unregister ipv6: Unknown symbol fib_rules_lookup ipv6: Unknown symbol inet6_lookup ipv6: Unknown symbol secure_tcpv6_sequence_number ipv6: Unknown symbol ipv6_skip_exthdr ipv6: Unknown symbol inet6_hash_connect ipv6: Unknown symbol ipv6_ext_hdr ipv6: Unknown symbol fib_rules_register ipv6: Unknown symbol __inet6_lookup_established ipv6: Unknown symbol __inet6_hash ipv6: Unknown symbol fib_rules_dump ipv6: Unknown symbol inet6_lookup_listener }}} ",ilvalle@… 3,530,LuCI: Please add list of mapped UPNP ports,fon-base-firmware,N/A,,enhancement,iurgi@…,investigate,2009-12-23T11:28:34Z,2012-12-19T15:51:38Z,"Please add two info screens to LuCI: * List of connected WLAN clients (with IPs) * List of currently open UPnP port forwardings",carsten.schuette@… 3,550,Support 3G dongle: Huawei E166,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2010-01-05T00:46:15Z,2012-12-26T17:42:08Z,"Recently our only phone operator added 3G support, they sell a huawei E166 usb modem along with the plan. now..... I got it to play nicely along with lafonera, but even though the modem shows itself as connected and registered to a network, I cant get internet :'( here's my connection status root@Fonera:~# cat /var/state/umtsd umtsd.umtsd.attached=1 umtsd.umtsd.device=option12D11001 umtsd.umtsdstate.vendor= umtsd.umtsdstate.model= umtsd.umtsdstate.provider=Kolbi ICE umtsd.umtsdstate.signal=19,99 umtsd.umtsdstate.state=ONLINE umtsd.umtsdstate.tx=3930 umtsd.umtsdstate.rx=8132 umtsd.umtsdstate.online=32 now in order for it to connect I had to change a few things. 1. data = USB0 2. cmd = USB2 also the apn is kolbi3g without user/password not sure about the DNS but used openDNS instead. laFonera reports it as connected to the network but no internet any help will be appreciated ",emudojo@… 3,559,Aliens can configure speedtouch modems,fon-network,N/A,,enhancement,john.crispin@…,investigate,2010-01-15T15:06:35Z,2013-02-20T23:40:04Z,"Any ISP that is using speedtouch modems allow access without password from the WAN side (it's locked from the ISP firewall)... The problem is that FON has not locked it from the PUBLIC side Someone just surf to checkip.dyndns.org then he copy&paste that ip in the adres bar of his browser and... he is now able to access the adsl modem of the fonero owner... the ISP stays ignorant...it's upto the fonero owner to secure his wifi... FON claims their solution is secure... how can FON make sure the fonera is NOT allowing access to the (changing) public side of their internet modem from the ""fon_public"" side? ",steven@… 3,580,Add ddns to /etc/hosts,fon-network,N/A,,enhancement,iurgi@…,confirmed,2010-02-07T18:00:32Z,2013-03-18T17:03:08Z,"Adding the ddns into the /etc/hosts I can use the ddns to deal with the fonera both inside and outside the network It's very easy and very useful !!! - Add the ddns to fonhosts.default.host using uci - Call SetupHosts ",ilvalle@… 3,584,Qos even for openvpn,fon-network,N/A,,enhancement,iurgi@…,infoneeded,2010-02-08T12:45:15Z,2012-12-19T16:59:56Z,I would like to set some limit to the vpn interface,ilvalle@… 3,586,Multi users accounts,fon-base-firmware,N/A,,enhancement,iurgi@…,investigate,2010-02-09T13:17:50Z,2010-11-03T21:55:15Z,"Now, we have only one user account for use and administer the Fonera. It would be also good to define other users who have no right to configure the Fonera (no admin rights), but the right to use the features and plugins that the administrator has authorised them to using. Users would also their own storage space on a USB drive plugged (no user could access to the storage space of another user except the administrator) and also an access to a common storage area for all users where they can delete only what they have added (except for the admin who can delete everything).",korbe@… 3,592,Enable RTSP conntrack,fon-network,N/A,,enhancement,iurgi@…,confirmed,2010-02-24T07:44:03Z,2012-12-19T17:11:01Z,"I'm a french user of Freebox (Internet Access Provider) which provides RTSP video channels, but I found that the fonera doesn't have ip_conntrack_rstp,ip_nat_rtsp so I use this service I got My box in modem mode, and the fonera for the router one Thanks In advance for adding theses modules",TeigneuX 3,597,Support 3G dongle: Sierra Wireless Compass 888,fon-network-3g,N/A,,enhancement,,investigate,2010-03-03T14:26:22Z,2012-12-19T17:12:37Z,"Hello, I'm trying to use my 3G Sierra Wireless Compass 888 to share my 3G connection. When I plug it the dongle is not recognised and appearing with the X in fonera's admin page. Here are the results of an usb devices cat. root@Fonera:~# cat /proc/bus/usb/devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.21 dwc_otg_hcd S: Product=DWC OTG Controller S: SerialNumber=lm0 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=0fff Rev= 0.00 S: Manufacturer=Sierra Wireless, Incorporated S: Product=USB MMC Storage S: SerialNumber=SWOC22905731 C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Any hint? Is the device planned to be supported? Cheers, Xavi.",xavierpalencia@… 3,606,JDownloader for Fonera2.0n,fon-plugins,N/A,,enhancement,iurgi@…,investigate,2010-03-19T22:21:45Z,2013-02-04T18:31:38Z,"I think is a great idea to implement Jdownloader in the fonera like transmission, installing it on the HD. Greetings!",Josemi 3,610,umts connection with no apn,fon-network-3g,N/A,,enhancement,john.crispin@…,investigate,2010-03-27T09:15:56Z,2013-03-11T01:00:57Z,"on new UMTS internet prepaid plans, the usage of APN, user and password is no longer needed. I have the FONERA 2.0g and i can't connect because the fonera ask me an APN, and if I put one the connection doesn't works. Thanks for helping me",theo_b24@… 3,654,enable wireless bridge - WDS,fon-wifi,N/A,,enhancement,iurgi@…,confirmed,2010-04-15T13:38:41Z,2013-02-14T21:17:14Z,"enable of WDS...it was available sth similar, but i could not get it to work Wireless bridge (also known as Wireless Distribution System or WDS) function allows you to connect to one or many APs through wireless. can u add this function in next or next next FW upgrade??",t00dyka@… 3,662,Amule for Fonera,unknown,N/A,,enhancement,iurgi@…,investigate,2010-04-19T18:30:35Z,2010-06-17T09:23:30Z,I think that it can be a great idea to give the option to install Amule in the hard drive as trasmission does (and jDownloader will be awesome),Josemi 3,663,SVN Subversion Server Plugin,unknown,N/A,,enhancement,iurgi@…,investigate,2010-04-19T18:40:39Z,2012-01-20T01:25:47Z,"I think that it can be a fantastic idea the creation of a Fon official plugin (as printer, music...) that be able to have a SVN Server in the fonera and have access to it thanks to dyndns. It doesn´t like very difficult.You can have a look at http://wiki.fon.com/wiki/F2_svn_server It can be a initial point, obviously I am wondering a plugin with GUI as music or webcam. Greetings",Josemi 3,664,Downloader Add-On for Internet Explorer,other,N/A,,enhancement,iurgi@…,investigate,2010-04-19T18:42:17Z,2010-06-17T09:30:34Z,"I think that it can be a must-have a version of the fonera downloader extension for Internet Explorer. Greetings",Josemi 3,665,Downloader Add-On for Opera,other,Other,,enhancement,iurgi@…,investigate,2010-04-19T18:42:51Z,2010-06-17T09:32:25Z,"I think that it can be a must-have a version of the fonera downloader extension for Opera. Greetings",Josemi 3,687,Support 3G dongles: Huawei E1550 and Onda MT503HS,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2010-05-10T21:11:28Z,2012-12-20T09:08:46Z,"Hello, on my LaFonera 2.0n I've tried to configure UMTS/3G, I've plugged in LaFonera 2.0n USB port my DataKey Huawei E1550, and I've selected custom configuration provided by my mobile company called Fastweb Mobile (not listed in default provider for Italy). I've inserted following credentials: APN: datacard.fastweb.it PIN: PIN of USIM Username: Password: DNS: (But I've tried to insert DNS provided by Fastweb Mobile) In ADVANCED CONFIGURATION, I've selected: Use Default DNS: Enabled and Disabled Network: UMTS Activate Hotspot: Disabled Everytime I've changed configuration parameters, I've restarted LaFonera 2.0n, but connection don't works! It try to connect with success (I see 3G logo on top right corner called ""Status""), but it disconnect after some seconds. I've LaFonera 2.0n latest end user firmware (Firmware Version: 2.3.6.0) I've tried with a Onda MT503HS key and it try to connect with success but for some seconds only, then disconnect like Huawei May you help me? Regards. P.S.: Please, for the next releases of LaFonera 2.0n firmware, may you add credentials about my Italian provider called Fastweb Mobile in dropdown list? Here credentials: For Datacard ONLY USIM: APN: datacard.fastweb.it Username: Password: Number: *99# DNS: AUTOMATIC For Voice & Data USIM: APN: apn.fastweb.it Username: Password: Number: *99# DNS: AUTOMATIC",morganfw@… 3,808,Support 3G dongle: Huawei E1750,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2010-05-23T13:27:24Z,2012-12-20T09:13:09Z,"I have followed the instructions at: http://trac.fonosfera.org/fon-ng/wiki/build revision 1666 My Huawei E1750 just says ""dailing in"" in the web gui but no connection. lsusb in a Linux box: Bus 001 Device 005: ID 12d1:1446 Huawei Technologies Co., Ltd. ",peter@… 3,809,Suuport 3G phone: HTC Desire,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2010-05-23T13:31:32Z,2013-03-14T11:54:52Z,"I have followed the instructions at http://trac.fonosfera.org/fon-ng/wiki/build and build revision 1666 I want to use my HTC desire as a 3G modem in my 2202 but it is not recognised as a modem. The HTC Desire works flawless as a modem in Ubuntu 9.10, 10.04 and others. lsusb at a linux box: Bus 001 Device 007: ID 0bb4:0ffe High Tech Computer Corp. ",peter@… 3,811,Support 3G dongle: Huawei e620,fon-network-3g,N/A,,enhancement,iurgi@…,investigate,2010-05-25T16:13:31Z,2012-12-20T09:19:29Z,"hi, the usb modem gets correctly recognized but is not able to connect yet. how do i try a manual connection ? i tried the umts script in Apps folder but it gives me errors",gabriele.vidali@… 3,814,Support 3G dongle: Option Icon 431,fon-network-3g,N/A,,enhancement,,investigate,2010-06-01T00:31:49Z,2012-12-20T09:19:57Z,"The option 3G dongle seems to be recognised by the fonera, but dialing in doesn't work. logread: ",bastian@… 3,819,Support 3G dongle: ZTE AC2726,fon-network-3g,N/A,,enhancement,matthijs,investigate,2010-06-02T19:03:58Z,2012-12-20T09:22:23Z,"please help me....very2 stressful.can't connect my ZTE AC2726 evdo modem..i had try all the configuration. from root@fonera (Putty) cat /proc/bus/usb/devices {{{ T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=19d2 ProdID=fff1 Rev= 0.00 S: Manufacturer=ZTE, Incorporated S: Product=ZTE CDMA Tech C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=128ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=87(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=88(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=08(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=86(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=89(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms }}} Apps/umtsd.lua {{{ config 'umtsdevice' 'option19D2FFF5' option 'data' '/dev/ttyUSB0' option 'cmd' '/dev/ttyUSB0' option 'vendor' 'ZTE' option 'model' 'AC2726' }}} umtsd.lua {{{ -- some dummy data local model local vendor local data = ""/dev/ttyUSB0"" local cmd = ""/dev/ttyUSB0"" }}} and {{{ local f = io.open(""/tmp/chat_umts"", ""w"") if f then f:write(""ABORT \""NO CARRIER\""\n"".. ""ABORT \""NO DIALTONE\""\n"".. ""ABORT \""ERROR\""\n"".. ""ABORT \""NO ANSWER\""\n"".. ""ABORT \""BUSY\""\n"".. ""\""\"" \""ATZ\""\n"".. ""OK \""ATH\""\n"".. ""OK AT+CGDCONT=1,\""IP\"",\""""..apn..""\""\n"".. ""OK \""ATD#777\""\n"".. ""\""CONNECT\"" \""\"""") f:close() service:start(unpack(params)) if service:status() == true then return ONLINE end }}} this is the logread {{{ root@Fonera:~# logread Feb 17 13:04:06 Fonera user.debug kernel: option 1-1:1.2: usb_probe_interface Feb 17 13:04:06 Fonera user.debug kernel: option 1-1:1.2: usb_probe_interface - got id Feb 17 13:04:06 Fonera user.info kernel: option 1-1:1.2: GSM modem (1-port) converter detected Feb 17 13:04:06 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 Feb 17 13:04:06 Fonera user.warn kernel: ttyusb -> 1 ttyUSB2 option 19D2FFF1 Feb 17 13:04:06 Fonera user.debug kernel: option 1-1:1.3: usb_probe_interface Feb 17 13:04:06 Fonera user.debug kernel: option 1-1:1.3: usb_probe_interface - got id Feb 17 13:04:06 Fonera user.info kernel: option 1-1:1.3: GSM modem (1-port) converter detected Feb 17 13:04:06 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3 Feb 17 13:04:06 Fonera user.warn kernel: ttyusb -> 1 ttyUSB3 option 19D2FFF1 Feb 17 13:04:06 Fonera user.debug kernel: option 1-1:1.4: usb_probe_interface Feb 17 13:04:06 Fonera user.debug kernel: option 1-1:1.4: usb_probe_interface - got id Feb 17 13:04:06 Fonera user.info kernel: option 1-1:1.4: GSM modem (1-port) converter detected Feb 17 13:04:06 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB4 Feb 17 13:04:06 Fonera user.warn kernel: ttyusb -> 1 ttyUSB4 option 19D2FFF1 Feb 17 13:04:06 Fonera user.info kernel: usbcore: registered new interface driver option Feb 17 13:04:06 Fonera user.info kernel: drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2 Feb 17 13:04:06 Fonera user.debug kernel: eth0.2: add 01:00:5e:00:00:01 mcast address to master interface Feb 17 13:04:06 Fonera user.info kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (1 port) Feb 17 13:04:06 Fonera user.info kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sierra USB modem (3 port) Feb 17 13:04:06 Fonera user.info kernel: usbcore: registered new interface driver sierra Feb 17 13:04:06 Fonera user.info kernel: drivers/usb/serial/sierra.c: USB Driver for Sierra Wireless USB modems: v.1.0.6 Feb 17 13:04:06 Fonera user.debug kernel: eth0.2: del 01:00:5e:00:00:01 mcast address from vlan interface Feb 17 13:04:06 Fonera user.debug kernel: eth0.2: del 01:00:5e:00:00:01 mcast address from master interface Feb 17 13:04:06 Fonera user.warn kernel: fuse init (API version 7.8) Feb 17 13:04:06 Fonera user.warn kernel: fuse distribution version: 2.7.3 Feb 17 13:04:06 Fonera user.info kernel: usbcore: registered new interface driver uvcvideo Feb 17 13:04:06 Fonera user.info kernel: USB Video Class driver (SVN r215) Feb 17 13:04:06 Fonera user.debug kernel: eth0.1: add 01:00:5e:00:00:01 mcast address to master interface Feb 17 13:04:07 Fonera user.info kernel: eth0.1: dev_set_promiscuity(master, 1) Feb 17 13:04:07 Fonera user.info kernel: device eth0 entered promiscuous mode Feb 17 13:04:07 Fonera user.info kernel: device eth0.1 entered promiscuous mode Feb 17 13:04:07 Fonera user.info kernel: br-lan: port 1(eth0.1) entering learning state Feb 17 13:04:07 Fonera user.info kernel: br-lan: topology change detected, propagating Feb 17 13:04:07 Fonera user.info kernel: br-lan: port 1(eth0.1) entering forwarding state Feb 17 13:04:07 Fonera user.notice root: serial is SVloKVT6YZ Feb 17 13:04:07 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:07 Fonera user.emerg syslog: 19d2:fff1 /etc/usb_modeswitch/19d2:fff1 Feb 17 13:04:07 Fonera user.emerg syslog: starting usb_modeswitch Feb 17 13:04:07 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:07 Fonera user.info : Looking for target devices ... Feb 17 13:04:07 Fonera user.info : No devices in target mode or class found Feb 17 13:04:07 Fonera user.info : Looking for default devices ... Feb 17 13:04:07 Fonera user.info : No default device found. Is it connected? Bye. Feb 17 13:04:08 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:08 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:08 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:08 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:08 Fonera user.emerg syslog: 3g hotplug Feb 17 13:04:09 Fonera user.info : ifconfig: SIOCGIFFLAGS: No such device Feb 17 13:04:09 Fonera user.info : rt3052(rt3052): disable failed Feb 17 13:04:09 Fonera user.info : sh: auto: bad number Feb 17 13:04:09 Fonera user.info : ifconfig: down: error fetching interface information: Device not found Feb 17 13:04:09 Fonera user.info : ifconfig: down: error fetching interface information: Device not found Feb 17 13:04:09 Fonera user.warn kernel: RX DESC a35e1000 size = 2048 Feb 17 13:04:09 Fonera user.warn kernel: <-- RTMPAllocTxRxRingMemory, Status=0 Feb 17 13:04:09 Fonera user.warn kernel: Key1Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key1Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key2Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key2Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key3Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key3Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key4Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: Key4Str is Invalid key length(0) or Type(0) Feb 17 13:04:09 Fonera user.warn kernel: 1. Phy Mode = 9 Feb 17 13:04:09 Fonera user.warn kernel: 2. Phy Mode = 9 Feb 17 13:04:09 Fonera user.warn kernel: 3. Phy Mode = 9 Feb 17 13:04:09 Fonera user.warn kernel: RTMPSetPhyMode: channel is out of range, use first channel=0 Feb 17 13:04:09 Fonera user.warn kernel: MCS Set = ff ff 00 00 01 Feb 17 13:04:09 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:09 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:09 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:09 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:10 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:10 Fonera user.notice kernel: scsi 0:0:0:0: Direct-Access ZTE USB Storage FFF1 2.31 PQ: 0 ANSI: 2 Feb 17 13:04:10 Fonera user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda Feb 17 13:04:10 Fonera user.debug kernel: usb-storage: device scan complete Feb 17 13:04:10 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:10 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:11 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:11 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:11 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:12 Fonera user.warn kernel: SYNC - BBP R4 to 20MHz.l Feb 17 13:04:12 Fonera user.warn kernel: Main bssid = 00:18:84:88:fd:64 Feb 17 13:04:12 Fonera user.warn kernel: <==== rt28xx_init, Status=0 Feb 17 13:04:12 Fonera user.warn kernel: 0x1300 = 00064320 Feb 17 13:04:12 Fonera user.info kernel: br-lan: port 1(eth0.1) entering disabled state Feb 17 13:04:13 Fonera user.info kernel: br-lan: port 1(eth0.1) entering learning state Feb 17 13:04:13 Fonera user.info kernel: br-lan: topology change detected, propagating Feb 17 13:04:13 Fonera user.info kernel: br-lan: port 1(eth0.1) entering forwarding state Feb 17 13:04:14 Fonera user.info kernel: device ra0 entered promiscuous mode Feb 17 13:04:14 Fonera user.info kernel: br-lan: port 2(ra0) entering learning state Feb 17 13:04:14 Fonera user.info kernel: br-lan: topology change detected, propagating Feb 17 13:04:14 Fonera user.info kernel: br-lan: port 2(ra0) entering forwarding state Feb 17 13:04:14 Fonera user.info : ifconfig ra1 down Feb 17 13:04:15 Fonera user.info : Loading defaults Feb 17 13:04:15 Fonera user.info : Loading synflood protection Feb 17 13:04:15 Fonera user.info : Adding custom chains Feb 17 13:04:16 Fonera user.info : Loading zones Feb 17 13:04:16 Fonera user.info : iptables: Chain already exists Feb 17 13:04:16 Fonera user.info : iptables: Chain already exists Feb 17 13:04:16 Fonera user.info : iptables: Chain already exists Feb 17 13:04:16 Fonera user.info : iptables: Chain already exists Feb 17 13:04:16 Fonera user.info : iptables: Chain already exists Feb 17 13:04:16 Fonera user.info : iptables: Chain already exists Feb 17 13:04:16 Fonera user.info : Loading rules Feb 17 13:04:16 Fonera user.info : Loading forwarding Feb 17 13:04:16 Fonera user.info : Loading redirects Feb 17 13:04:16 Fonera user.info : Loading includes Feb 17 13:04:16 Fonera user.info : /etc/firewall.fon Feb 17 13:04:16 Fonera user.info : FWallFON Feb 17 13:04:17 Fonera user.info : FWallDaemon Feb 17 13:04:17 Fonera user.info : killall: chilli: no process killed Feb 17 13:04:17 Fonera user.notice root: adding br-lan to firewall zone lan Feb 17 13:04:18 Fonera user.notice root: adding tun-ovpn to firewall zone vpn Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: Found user 'nobody' (UID 65534) and group 'nogroup' (GID 65534). Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: Successfully dropped root privileges. Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: avahi-daemon 0.6.25 starting up. Feb 17 13:04:18 Fonera daemon.warn avahi-daemon[1508]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns! Feb 17 13:04:18 Fonera daemon.warn avahi-daemon[1508]: Failed to open /etc/resolv.conf: No such file or directory Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: No service file found in /tmp/mdns/. Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: Joining mDNS multicast group on interface br-lan.IPv4 with address 192.168.10.1. Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: New relevant interface br-lan.IPv4 for mDNS. Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: Network interface enumeration completed. Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: Registering new address record for 192.168.10.1 on br-lan.IPv4. Feb 17 13:04:18 Fonera daemon.info avahi-daemon[1508]: Registering HINFO record with values 'MIPS'/'LINUX'. Feb 17 13:04:19 Fonera user.notice root: setting up led : powerg Feb 17 13:04:19 Fonera daemon.info avahi-daemon[1508]: Server startup complete. Host name is Fonera.local. Local service cookie is 747774664. Feb 17 13:04:19 Fonera user.notice root: setting up led : wifi Feb 17 13:04:19 Fonera user.crit syslog: fonstated - v2.0 Feb 17 13:04:19 Fonera user.crit fonstated: loaded fontimer for ""/bin/thinclient dummy"" period=17280 Feb 17 13:04:19 Fonera user.crit fonstated: loaded fontimer for ""/etc/fonstated/RestartNtpclient"" period=17280 Feb 17 13:04:19 Fonera user.crit fonstated: loaded fontimer for ""/etc/init.d/fonsmcd"" period=12 Feb 17 13:04:19 Fonera user.crit fonstated: loaded fontimer for ""/etc/fonstated/StartHttpd"" period=2150 Feb 17 13:04:19 Fonera user.crit fonstated: starting chillispot fonstate plugin Feb 17 13:04:19 Fonera user.crit fonstated: added fontimer libcallback period=60 Feb 17 13:04:19 Fonera user.crit fonstated: added fontimer libcallback period=17280 Feb 17 13:04:19 Fonera user.crit fonstated: added fonevent hotspot_decount -> libcallback 1 Feb 17 13:04:19 Fonera user.crit fonstated: added fonevent hotspot_inccount -> libcallback 1 Feb 17 13:04:19 Fonera user.crit fonstated: added fonevent hotspot_resetcount -> libcallback 1 Feb 17 13:04:19 Fonera user.crit fonstated: added fonevent hotspot_wdt_start -> libcallback 1 Feb 17 13:04:19 Fonera user.crit fonstated: added fonevent hotspot_wdt_stop -> libcallback 1 Feb 17 13:04:19 Fonera user.crit fonstated: enqueue --> UMTS Feb 17 13:04:19 Fonera user.crit fonstated: enqueue --> SetupHosts Feb 17 13:04:19 Fonera user.crit fonstated: enqueue --> BootServices Feb 17 13:04:19 Fonera user.crit fonstated: enqueue --> FWallDaemon Feb 17 13:04:19 Fonera user.crit fonstated: enqueue --> StartTorrent Feb 17 13:04:19 Fonera user.crit fonstated: running event /etc/fonstated/UMTS Feb 17 13:04:20 Fonera user.notice root: runnow --> /etc/fonstated/ConfigFON Feb 17 13:04:21 Fonera user.notice root: runnow --> /etc/fonstated/ConfigWan Feb 17 13:04:22 Fonera user.notice root: scan_umts Feb 17 13:04:22 Fonera user.notice root: scan_umts Feb 17 13:04:22 Fonera user.crit fonstated: finished running /etc/fonstated/UMTS Feb 17 13:04:22 Fonera user.crit fonstated: running event /etc/fonstated/SetupHosts Feb 17 13:04:22 Fonera user.crit fonstated: finished running /etc/fonstated/SetupHosts Feb 17 13:04:22 Fonera user.crit fonstated: running event /etc/fonstated/BootServices Feb 17 13:04:22 Fonera user.notice root: scan_umts Feb 17 13:04:22 Fonera user.notice root: runnow --> /etc/fonstated/Redirect Feb 17 13:04:23 Fonera user.notice root: runnow --> /etc/fonstated/StartFonsmcd Feb 17 13:04:23 Fonera user.notice root: runnow --> /etc/fonstated/RestartMountd Feb 17 13:04:23 Fonera user.notice root: runnow --> /etc/fonstated/StartHttpd Feb 17 13:04:23 Fonera user.crit mountd[1882]: Starting OpenWrt (auto)mountd V1 Feb 17 13:04:24 Fonera user.crit mountd[1882]: trying to mount /tmp/run/mountd/ as the autofs root Feb 17 13:04:24 Fonera user.crit fonstated: finished running /etc/fonstated/BootServices Feb 17 13:04:24 Fonera user.crit fonstated: running event /etc/fonstated/FWallDaemon Feb 17 13:04:24 Fonera user.notice root: runnow --> /etc/fonstated/SetupDlmd Feb 17 13:04:25 Fonera authpriv.info dropbear[1919]: Not backgrounding Feb 17 13:04:25 Fonera user.crit fonstated: finished running /etc/fonstated/FWallDaemon Feb 17 13:04:25 Fonera user.crit fonstated: running event /etc/fonstated/StartTorrent Feb 17 13:04:25 Fonera user.crit fonstated: finished running /etc/fonstated/StartTorrent Feb 17 13:04:25 Fonera user.emerg syslog: starting onlined Feb 17 13:04:25 Fonera daemon.info avahi-daemon[1508]: Got SIGHUP, reloading. Feb 17 13:04:25 Fonera daemon.info avahi-daemon[1508]: Loading service file /tmp/mdns//smb.service. Feb 17 13:04:25 Fonera daemon.warn avahi-daemon[1508]: Failed to open /etc/resolv.conf: No such file or directory Feb 17 13:04:25 Fonera user.crit fonstated: enqueue --> StartFonsmcd Feb 17 13:04:25 Fonera user.crit fonstated: running event /etc/fonstated/StartFonsmcd Feb 17 13:04:25 Fonera user.crit fonstated: finished running /etc/fonstated/StartFonsmcd Feb 17 13:04:26 Fonera daemon.info avahi-daemon[1508]: Service ""LaFonera"" (/tmp/mdns//smb.service) successfully established. Feb 17 13:04:26 Fonera daemon.info avahi-daemon[1508]: Got SIGHUP, reloading. Feb 17 13:04:26 Fonera daemon.info avahi-daemon[1508]: Loading service file /tmp/mdns//ssh.service. Feb 17 13:04:26 Fonera daemon.warn avahi-daemon[1508]: Failed to open /etc/resolv.conf: No such file or directory Feb 17 13:04:26 Fonera user.notice root: runnow --> /etc/fonstated/FWallDaemon Feb 17 13:04:27 Fonera daemon.info avahi-daemon[1508]: Service ""Fonera2.0 SSH"" (/tmp/mdns//ssh.service) successfully established. Feb 17 13:04:28 Fonera daemon.info dnsmasq[2027]: started, version 2.45 cachesize 150 Feb 17 13:04:28 Fonera daemon.info dnsmasq[2027]: compile time options: IPv6 GNU-getopt ISC-leasefile no-DBus no-I18N TFTP Feb 17 13:04:28 Fonera daemon.info dnsmasq[2027]: DHCP, IP range 192.168.10.100 -- 192.168.10.250, lease time 12h Feb 17 13:04:28 Fonera user.info syslog: whitelist file: /etc/fon/whitelist.dnsmasq Feb 17 13:04:28 Fonera daemon.info dnsmasq[2027]: using local addresses only for domain lan Feb 17 13:04:28 Fonera daemon.warn dnsmasq[2027]: failed to access /tmp/resolv.conf.auto: No such file or directory Feb 17 13:04:28 Fonera daemon.info dnsmasq[2027]: read /etc/hosts - 2 addresses Feb 17 13:04:28 Fonera daemon.err dnsmasq[2027]: failed to read /etc/ethers:No such file or directory Feb 17 13:04:34 Fonera daemon.info fonsmcd[1866]: Sucessfully started Feb 17 13:04:55 Fonera user.crit fonstated: enqueue --> HotspotStop Feb 17 13:04:55 Fonera user.crit fonstated: running event /etc/fonstated/HotspotStop Feb 17 13:04:56 Fonera user.crit fonstated: finished running /etc/fonstated/HotspotStop Feb 17 13:05:28 Fonera authpriv.info dropbear[3600]: Child connection from 192.168.10.239:1882 Feb 17 13:05:34 Fonera authpriv.notice dropbear[3600]: password auth succeeded for 'root' from 192.168.10.239:1882 }}} ",amanullang@… 3,833,USB Disc settings doesn't list device numbers,fon-base-firmware,2.3.7.0 rc2,,enhancement,,confirmed,2010-06-17T17:53:53Z,2012-12-20T10:02:08Z,"When looking in the filebrowser disks are identified by their name. In the case when they haven't been named yet, names like ""Disc-A1"" are used. When looking in the USB disc page on the dashboard, a list of disks (partitions) is presented, identified by the size of the partition. This page allows giving each partition a more friendly name, so it is easier to tell them apart. However, there is no clear way to tell the partitions apart, if you don't know the sizes in advance. If there are partitions with identical size, there is really no way. You can't use the filebrowser to see which disk is which, since the filebrowser doesn't list these sizes. I guess it would be useful to add the current name of each disc to the USB discs page (probably only when the setting is still ""Automatic"").",matthijs 3,840,K3765 from vodafone in Netherlands not recognised,fon-network-3g,N/A,,enhancement,,investigate,2010-06-23T20:44:53Z,2012-12-20T10:06:07Z,"Dear friends, I just received my fonera 2.0n and installed latest firmware 2.3.6.0 My vodafone dongle K3765 is not recognised thus I cannot use the fonera. I tried several settings in the UMTS/3G section but none helped. I found a discussion on http://www.mail-archive.com/wireless@ml.ninux.org/msg02277.html where somebody managed to get the K3765 running but this seems to be linux tools and I am no expert in Linux. Hope you can help, marcel",m.wittebrood@… 3,841,Force DNS requests to the Fonera,fon-base-firmware,N/A,,enhancement,,investigate,2010-06-24T10:14:21Z,2013-01-12T13:55:54Z,"The Fonera-productline is the only accesspoint/router that does not have any 'parental' filter features... For a hotspot service that allows aliens to connect to your internet connection this is a big fail! Perhaps it would be interesting to support OpenDns FamilyShield : https://www.opendns.com/familyshield/ At the moment it is possible to add eg the Dns of Opendns... but anyone who wants to use another ""dns"" server is allowed to do so The IpTables on La Fonera will not send all DNS traffic to the configured opendns... This also allows people to use DNS-tunnelling to avoid the Fonera Captive Portal ",steven@… 3,847,Support 3G dongle: Samsung GT-B3730,fon-network-3g,N/A,,enhancement,,investigate,2010-06-30T11:56:12Z,2012-12-20T10:11:21Z,I'd love support for the new samsung GT-B3730 2g/3g/4g modem in the fon router software!,viktor@… 3,850,File sharing user right management (FTP & Samba),fon-base-firmware,N/A,,enhancement,,confirmed,2010-07-05T06:02:22Z,2012-12-24T10:42:33Z,"I think it is absolutely important to intergarte an adequate user right management for the ftp server. The ftp server is not useable as it is right now, only offering a master user login and a anonymous login which accesses the same folders. ",t031 3,876,Support 3G dongle: Huawei E1820,fon-network-3g,N/A,,enhancement,,investigate,2010-08-07T23:03:30Z,2012-12-20T09:45:44Z,"i tested my 3G dongle today, and it doesn't work.. i don't see any errors in the logs, but there is no internet connection, and the UMTS/3G page shows that it is still dialing in. This is without a hub, directly to the fonera. its a T-Mobile NL Huawei E1820 logread gave a lot of onlined messages.. {{{ root@Fonera:~# logread -f Jul 13 21:59:25 Fonera user.emerg syslog: onlined: failed to resolve hostname updates.fon.com: No such file or directory }}} so i grep'd them away.. {{{ root@Fonera:~# logread -f|grep -v 'onlined: failed' Jul 13 21:59:53 Fonera user.debug kernel: hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 Jul 13 21:59:53 Fonera user.debug kernel: hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s Jul 13 21:59:54 Fonera user.debug kernel: hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 Jul 13 21:59:54 Fonera user.info kernel: usb 1-1: new high speed USB device using dwc_otg and address 2 Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1: default language 0x0409 Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1: new device strings: Mfr=3, Product=2, SerialNumber=0 Jul 13 21:59:54 Fonera user.info kernel: usb 1-1: Product: HUAWEI Mobile Jul 13 21:59:54 Fonera user.info kernel: usb 1-1: Manufacturer: Huawei Technologies Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1: uevent Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1: usb_probe_device Jul 13 21:59:54 Fonera user.info kernel: usb 1-1: configuration #1 chosen from 1 choice Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1: adding 1-1:1.0 (config #1, interface 0) Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1:1.0: uevent Jul 13 21:59:54 Fonera user.debug kernel: usb-storage 1-1:1.0: usb_probe_interface Jul 13 21:59:54 Fonera user.debug kernel: usb-storage 1-1:1.0: usb_probe_interface - got id Jul 13 21:59:54 Fonera user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1: adding 1-1:1.1 (config #1, interface 1) Jul 13 21:59:54 Fonera user.debug kernel: usb 1-1:1.1: uevent Jul 13 21:59:54 Fonera user.debug kernel: usb-storage 1-1:1.1: usb_probe_interface Jul 13 21:59:54 Fonera user.debug kernel: usb-storage 1-1:1.1: usb_probe_interface - got id Jul 13 21:59:54 Fonera user.debug kernel: usb-storage: device found at 2 Jul 13 21:59:54 Fonera user.debug kernel: usb-storage: waiting for device to settle before scanning Jul 13 21:59:54 Fonera user.info kernel: scsi1 : SCSI emulation for USB Mass Storage devices Jul 13 21:59:54 Fonera user.debug kernel: drivers/usb/core/inode.c: creating file '002' Jul 13 21:59:54 Fonera user.debug kernel: hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 Jul 13 21:59:54 Fonera user.debug kernel: hub 1-0:1.0: port 1 enable change, status 00000503 Jul 13 21:59:54 Fonera user.debug kernel: usb-storage: device found at 2 Jul 13 21:59:54 Fonera user.debug kernel: usb-storage: waiting for device to settle before scanning Jul 13 21:59:54 Fonera user.emerg syslog: 3g hotplug Jul 13 21:59:54 Fonera user.emerg syslog: 12d1:1446 /etc/usb_modeswitch/12d1:1446 Jul 13 21:59:54 Fonera user.emerg syslog: starting usb_modeswitch Jul 13 21:59:54 Fonera user.debug kernel: usb-storage 1-1:1.0: disconnect by usbfs Jul 13 21:59:54 Fonera user.debug kernel: usbdev1.2_ep81: ep_device_release called for usbdev1.2_ep81 Jul 13 21:59:54 Fonera user.debug kernel: usbdev1.2_ep01: ep_device_release called for usbdev1.2_ep01 Jul 13 21:59:54 Fonera user.debug kernel: usbdev1.2_ep81: ep_device_release called for usbdev1.2_ep81 Jul 13 21:59:54 Fonera user.debug kernel: usbdev1.2_ep01: ep_device_release called for usbdev1.2_ep01 Jul 13 21:59:54 Fonera user.emerg syslog: 3g hotplug Jul 13 21:59:54 Fonera user.warn kernel: usb 1-1: usbfs: process 1901 (usb_modeswitch) did not claim interface 0 before use Jul 13 21:59:54 Fonera user.info : Looking for target devices ... Jul 13 21:59:54 Fonera user.info : No devices in target mode or class found Jul 13 21:59:54 Fonera user.info : Looking for default devices ... Jul 13 21:59:54 Fonera user.info : Found default devices (1) Jul 13 21:59:54 Fonera user.info : Accessing device 002 on bus 001 ... Jul 13 21:59:54 Fonera user.info : Using endpoints 0x01 (out) and 0x81 (in) Jul 13 21:59:54 Fonera user.info : Inquiring device details; driver will be detached ... Jul 13 21:59:54 Fonera user.info : Looking for active driver ... Jul 13 21:59:54 Fonera user.info : OK, driver found (""usb-storage"") Jul 13 21:59:54 Fonera user.info : OK, driver ""usb-storage"" detached Jul 13 21:59:54 Fonera user.info : SCSI inquiry data (for identification) Jul 13 21:59:54 Fonera user.info : ------------------------- Jul 13 21:59:54 Fonera user.info : Vendor String: HUAWEI Jul 13 21:59:54 Fonera user.info : Model String: Mass Storage Jul 13 21:59:54 Fonera user.info : Revision String: 2.31 Jul 13 21:59:54 Fonera user.info : ------------------------- Jul 13 21:59:54 Fonera user.info : USB description data (for identification) Jul 13 21:59:54 Fonera user.info : ------------------------- Jul 13 21:59:54 Fonera user.info : Manufacturer: Huawei Technologies Jul 13 21:59:54 Fonera user.info : Product: HUAWEI Mobile Jul 13 21:59:54 Fonera user.info : Serial No.: not provided Jul 13 21:59:54 Fonera user.info : ------------------------- Jul 13 21:59:54 Fonera user.info : Setting up communication with interface 0 ... Jul 13 21:59:54 Fonera user.info : Trying to send the message to endpoint 0x01 ... Jul 13 21:59:54 Fonera user.emerg syslog: 3g hotplug Jul 13 21:59:54 Fonera user.debug kernel: hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 Jul 13 21:59:54 Fonera user.debug kernel: hub 1-0:1.0: port 1 enable change, status 00000500 Jul 13 21:59:54 Fonera user.err kernel: hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling... Jul 13 21:59:54 Fonera user.debug kernel: hub 1-0:1.0: port 1, status 0500, change 0002, 480 Mb/s Jul 13 21:59:54 Fonera user.info kernel: usb 1-1: USB disconnect, address 2 Jul 13 21:59:59 Fonera user.debug kernel: usb-storage: device scan complete Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1: usb_modeswitch timed out on ep0out len=0/0 Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1: unregistering device Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1: usb_disable_device nuking all URBs Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1: unregistering interface 1-1:1.0 Jul 13 21:59:59 Fonera user.debug kernel: usbdev1.2_ep81: ep_device_release called for usbdev1.2_ep81 Jul 13 21:59:59 Fonera user.debug kernel: usbdev1.2_ep01: ep_device_release called for usbdev1.2_ep01 Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1:1.0: uevent Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1: unregistering interface 1-1:1.1 Jul 13 21:59:59 Fonera user.debug kernel: usbdev1.2_ep02: ep_device_release called for usbdev1.2_ep02 Jul 13 21:59:59 Fonera user.debug kernel: usbdev1.2_ep82: ep_device_release called for usbdev1.2_ep82 Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1:1.1: uevent Jul 13 21:59:59 Fonera user.debug kernel: usbdev1.2_ep00: ep_device_release called for usbdev1.2_ep00 Jul 13 21:59:59 Fonera user.debug kernel: usb 1-1: uevent Jul 13 21:59:59 Fonera user.debug kernel: hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 Jul 13 21:59:59 Fonera user.debug kernel: hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s Jul 13 21:59:59 Fonera user.emerg syslog: 3g hotplug Jul 13 21:59:59 Fonera user.emerg syslog: 3g hotplug Jul 13 21:59:59 Fonera user.debug kernel: hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 Jul 13 21:59:59 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: new high speed USB device using dwc_otg and address 3 Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: default language 0x0409 Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: new device strings: Mfr=3, Product=2, SerialNumber=0 Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: Product: HUAWEI Mobile Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: Manufacturer: Huawei Technologies Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: uevent Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: usb_probe_device Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: configuration #1 chosen from 1 choice Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: adding 1-1:1.0 (config #1, interface 0) Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1:1.0: uevent Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.0: usb_probe_interface Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.0: usb_probe_interface - got id Jul 13 22:00:00 Fonera user.info kernel: option 1-1:1.0: GSM modem (1-port) converter detected Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 Jul 13 22:00:00 Fonera user.warn kernel: ttyusb -> 1 ttyUSB0 option 12D114AC Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: adding 1-1:1.1 (config #1, interface 1) Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1:1.1: uevent Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.1: usb_probe_interface Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.1: usb_probe_interface - got id Jul 13 22:00:00 Fonera user.info kernel: option 1-1:1.1: GSM modem (1-port) converter detected Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 Jul 13 22:00:00 Fonera user.warn kernel: ttyusb -> 1 ttyUSB1 option 12D114AC Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: adding 1-1:1.2 (config #1, interface 2) Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1:1.2: uevent Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.2: usb_probe_interface Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.2: usb_probe_interface - got id Jul 13 22:00:00 Fonera user.info kernel: option 1-1:1.2: GSM modem (1-port) converter detected Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 Jul 13 22:00:00 Fonera user.warn kernel: ttyusb -> 1 ttyUSB2 option 12D114AC Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: adding 1-1:1.3 (config #1, interface 3) Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1:1.3: uevent Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.3: usb_probe_interface Jul 13 22:00:00 Fonera user.debug kernel: option 1-1:1.3: usb_probe_interface - got id Jul 13 22:00:00 Fonera user.info kernel: option 1-1:1.3: GSM modem (1-port) converter detected Jul 13 22:00:00 Fonera user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3 Jul 13 22:00:00 Fonera user.warn kernel: ttyusb -> 1 ttyUSB3 option 12D114AC Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: adding 1-1:1.4 (config #1, interface 4) Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1:1.4: uevent Jul 13 22:00:00 Fonera user.debug kernel: usb-storage 1-1:1.4: usb_probe_interface Jul 13 22:00:00 Fonera user.debug kernel: usb-storage 1-1:1.4: usb_probe_interface - got id Jul 13 22:00:00 Fonera user.info kernel: scsi2 : SCSI emulation for USB Mass Storage devices Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1: adding 1-1:1.5 (config #1, interface 5) Jul 13 22:00:00 Fonera user.debug kernel: usb 1-1:1.5: uevent Jul 13 22:00:00 Fonera user.debug kernel: usb-storage 1-1:1.5: usb_probe_interface Jul 13 22:00:00 Fonera user.debug kernel: usb-storage 1-1:1.5: usb_probe_interface - got id Jul 13 22:00:00 Fonera user.debug kernel: usb-storage: device found at 3 Jul 13 22:00:00 Fonera user.debug kernel: usb-storage: waiting for device to settle before scanning Jul 13 22:00:00 Fonera user.info kernel: scsi3 : SCSI emulation for USB Mass Storage devices Jul 13 22:00:00 Fonera user.debug kernel: drivers/usb/core/inode.c: creating file '003' Jul 13 22:00:00 Fonera user.debug kernel: hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 Jul 13 22:00:00 Fonera user.debug kernel: hub 1-0:1.0: port 1 enable change, status 00000503 Jul 13 22:00:00 Fonera user.debug kernel: usb-storage: device found at 3 Jul 13 22:00:00 Fonera user.debug kernel: usb-storage: waiting for device to settle before scanning Jul 13 22:00:00 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:00 Fonera user.emerg syslog: 12d1:14ac /etc/usb_modeswitch/12d1:14ac Jul 13 22:00:00 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:00 Fonera user.info : OK, message successfully sent Jul 13 22:00:00 Fonera user.info : Device is gone, skipping any further commands Jul 13 22:00:00 Fonera user.info : Checking for mode switch (max. 20 times, once per second) ... Jul 13 22:00:00 Fonera user.info : Original device is gone already, not checking Jul 13 22:00:00 Fonera user.info : Searching for target devices ... Jul 13 22:00:00 Fonera user.info : Found correct target device Jul 13 22:00:00 Fonera user.info : Mode switch succeeded. Bye. Jul 13 22:00:00 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:00 Fonera user.crit fonstated: enqueue --> UMTS Jul 13 22:00:00 Fonera user.crit fonstated: running event /etc/fonstated/UMTS Jul 13 22:00:00 Fonera user.notice root: runnow --> /etc/fonstated/ConfigFON Jul 13 22:00:01 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:01 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:01 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:01 Fonera user.emerg syslog: 3g hotplug Jul 13 22:00:02 Fonera user.notice root: runnow --> /etc/fonstated/ConfigWan Jul 13 22:00:03 Fonera user.notice root: scan_umts Jul 13 22:00:03 Fonera user.notice root: scan_umts Jul 13 22:00:03 Fonera user.crit fonstated: finished running /etc/fonstated/UMTS Jul 13 22:00:05 Fonera user.notice kernel: scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 Jul 13 22:00:05 Fonera user.notice kernel: scsi 3:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 Jul 13 22:00:05 Fonera user.notice kernel: sd 3:0:0:0: Attached scsi removable disk sda Jul 13 22:00:05 Fonera user.debug kernel: usb-storage: device scan complete Jul 13 22:00:05 Fonera user.debug kernel: usb-storage: device scan complete }}} in the /etc/usb_modeswitch/ dir i do find the right id: 12d1:1446 and it looks like the modeswitch goes OK as well. i tried umount-ing the cd-drive.. but that didn't help",koter84@… 3,885,Support for multiple printers,fon-plugin-printer,2.3.7.0 rc2,,enhancement,,confirmed,2010-08-25T09:26:36Z,2012-12-20T11:53:57Z,"Hi! I want to share 2 printers on my fonera but can only get 1 at a time to work. I have an Epson printer and a Canon fax printer and when I first plug-in the Epson printer to my hub (that's connected to the Fonera), it works fine. But when I plug-in the Canon fax printer too, the Epson printer won't work! It disappears in the printer settings menu in the Fon GUI and it's not possible to print by using port 9100. Doesn't the fonera support multiple printers? Do I have to use another port? Regards, Henrik",anonymous 3,887,"After installing update Fonera, Tranmission needs reinstall",fon-plugin-transmission,N/A,,enhancement,,confirmed,2010-08-25T14:11:32Z,2013-04-24T09:36:38Z,"Problem: I updated the Fonera 2.0n from Gari to Gari junior. After installing the update, I clicked on torrent on FON Router GUI page. There was only a install button available. Solution: I did not understand it, because the torrent plugin has nothing to do with the Fonera update. I looked at the FoneraApps folder and I discovered why it was not working. Because the version-number changes, the torrent file names change too. I updated the file names and Tranmission is up and running again. [[Image(http://img839.imageshack.us/img839/1139/fonera20ntranmissionlos.png)]]",calvinturbo@… 3,906,Support 3G dongle: Huawei E122,fon-network-3g,N/A,,enhancement,,investigate,2010-09-05T11:31:04Z,2012-12-20T13:55:24Z,I am unable to get the Huawei E122 modem to work with the Fonera 2.0n router. This modem is supplied by the three.ie telecommunications company. I have installed the latest firmware 2.3.6.0 on the Fonera 2.0n but the modem is still not recognised.,ptpjre@… 3,922,Download files into subdirectories,fon-plugin-downloader,N/A,,enhancement,,confirmed,2010-09-16T02:03:23Z,2012-12-20T12:26:09Z,"Can you add a function that allow to download manager of move the downloaded file in a directory that has the same name inserted when add a new download? See the attached for an example",ddomee@… 3,929,Support 3G dongles: Huawei E1752 and Ovation MC990D,fon-network-3g,N/A,,enhancement,,investigate,2010-09-23T11:48:34Z,2012-12-20T13:30:55Z,"I have two different modems, and non of them have been recognized. Modem: Huawei E1752 Recognized as USB drive Modem: Ovation MC990D Not recognized as USB drives I would need to use any of them (or both) to be work with the Fonera 2.0n Regards,",vigoabad@… 3,954,Support 3G dongle: K3570-Z,fon-network-3g,N/A,,enhancement,,investigate,2010-10-25T16:52:08Z,2012-12-20T14:29:45Z,"Modem not recognized by Fonera 2.0g with 2.3.0.1 Firmware. Tried with and without USB 2.0 unpowered hub .",decodecoding 3,974,scheduling wifi on and off,fon-wifi,N/A,,enhancement,,confirmed,2010-11-17T21:11:10Z,2012-12-19T09:50:23Z,"Possible enhancement: a small program to schedule the power on and off of the wifi connection. That' s in order to limit the wave radio pollution and energy consumption.",notizie_varie@… 3,989,Support 3G dongle: Nokia CS-17,fon-network-3g,N/A,,enhancement,,investigate,2010-12-20T16:34:29Z,2012-12-20T10:01:45Z,"Hi, this is a long one. I've had a couple of Fonera 2.0n:s for about a year or so and finally thought of contacting you guys. Been struggling for the whole time to get an UMTS device working. The support for the Nokia CS-17 Internet Stick, Huawei E1820 and Huawei E169 would be -very, very- much apprecciated, in this order of importance. As long as you haven't had a CS-17 in a linux machine before, it even comes with it's own variety of Linux drivers. Maybe they would be of help? I made the mistake of installing the ""nokiainternetmodem.deb"" package so can't find any way to get my hands back to the ZeroCD drivers, which apparently are nowhere else to be found. At the moment (10/12/20), Linux Mint 10 does not recognize the stick at all, and Ubuntu 10 does the same after I removed the driver package to get my hands back to the ZeroCD files. Apparently Nokia's modeswitch shows different disk content for Windows and Linux enviroments. Anyway, in my opinion the trouble with Fonera 2.0n is the lack of real support for umts-modems. Whereas other routers got a pull-down menu where to choose the right make+model from, the Fonera2 seems to try going around ZeroCDs with only the usb-modeswitch, some luck and with a very general set of commands. So far I modified at least the developer firmwares 2.3.6.1 and 2.3.6 (since SSH access is required to modify the files) and got unstable but usable connectivity with a Huawei E169. It takes less than 24h for the system to choke. Removing the dongle for a while might help, but normally a full power off is required. Got a powered USB-hub for it, too. With the dongle connected the overall system performance drops like the tail of a cow. My quick and dirty fixes for the E169 were based mainly on http://wiki.fon.com/wiki/FON2-Tweak-3G-Irish3 , modifying numbers of the used usb-devices, '/dev/ttyUSB0' etc. With the recent Nokia CS-17 I tried another approach with the usb-modeswitch, introducing it in ""/etc/config/network"" as ""config 'interface' 'ppp0'"" and updating the ""/etc/config/firewall"" with lines option 'mtu_fix' '1' option 'network' 'wan ppp0' , but in the end couldn't get usb-modeswitch to ""eject"" the drive. ""cat /proc/bus/usb/devices"" gave me these values for the stick: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0421 ProdID=0622 Rev= 0.01 S: Manufacturer=Nokia S: Product=Nokia Datacard S: SerialNumber= Icanhaz hidden C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms root@Fonera:/etc/usb_modeswitch# I used vi to create the file /etc/usb-modeswitch.conf with values: ###################################### # Nokia CS-17 Internet Stick DefaultVendor= 0x0421 DefaultProduct=0x0622 TargetVendor= 0x0421 TargetProductList=""1001,1406,140c,14ac"" CheckSuccess=20 MessageContent=""55534243123456780000000000000011060000000000000000000000000000"" The last 3 lines were completely random from some website configuring a Huawei to a linux desktop enviroment (slackware?), so that could be the problem. Windows device management gave me Hardware ids VID_0421&PID_0624 for the installed CS-17 modem driver. I really hope this would help and Finally make the 3G project take some steps ahead. I could really use the USB 3G support since it's the only means of connecting and the main reason why I got the boxes in the 1st place. If it would be more stable, the Fonspot sharing would also serve the purpose better. I understand a bit more out of these than an average pig out of a moon rocket, but seems like many people are even more confused with the Fonera 2.0n 3G issues than I am. Let's get this thing on the move, eh? Cheers and merry christmas, Juha the Flying Finn ",fzs_@… 3,1023,Support 3G dongle: Huawei E173,fon-network-3g,N/A,,enhancement,,investigate,2011-03-13T21:17:28Z,2013-01-08T14:54:53Z,"Hello friends, here are the content of the file /proc/bus/usb/devices: {{{ T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 3 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.26.2 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:00.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev= 0.00 S: Manufacturer=HUAWEI Technology S: Product=HUAWEI Mobile C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms }}} what I have to change in the configuration at the router? Greets from Berlin Dirk ",dirk.grabner@… 3,1025,Port forwarding does not work from the internal network,fon-network,2.3.6.1 (Gari jr.),,enhancement,,investigate,2011-03-24T09:07:06Z,2012-12-19T12:47:39Z,"Due to a limitation in how DNAT forwarding works, a port forward set up in the Settings -> Firewall -> Port forwarding section does not work from the internal LAN. This is a well-known problem for port forwarding, which I'll illustrate with an example. Say way forward port 1000 to a server at 192.168.1.100. Suppose the public address of our Fonera is 203.0.113.1. When a client connects from the internet to 203.0.113.1:1000, the Fonera receives the request packet on its WAN port, changes the destination address into 192.168.1.100:1000 and sends it to the server on the LAN network. The server processes the request and sends a reply back to the internet client. This reply has to pass the Fonera on its way to the internet, where the Fonera can change the source address this time, from the 192.168.1.100 set by the server to 203.0.113.1 again (which is what the internet client expects). Now, when a client from the LAN, say 192.168.1.200, connects to 203.0.113.1, things get different. The packet gets passed to the Fonera (on its LAN port), since the client thinks it should go onto the internet. The Fonera then changes the destination address into 192.168.1.100 and sends the request off to the server. The source address of the request packet is unmodified, so it's still 192.168.1.200. This means the reply packet gets sent to 192.168.1.200 as well. The server can now send this reply directly to the client, bypassing the Fonera, since it knows the client is on the same network. However, this also means that the Fonera does not get the chance to ""undo"" the address translation on the reply packet. The client now gets a reply from the server, 192.168.1.100, but it has sent a request to the WAN ip, 203.0.113.1, so it discards the packet. Hence, using just a DNAT rule for port forwarding doesn't work for internal requests. There is a solution for this: When a request comes from the internal network, do SNAT in addition to DNAT. This also rewrites the source address of a packet, making it look like it comes from the Fonera. This causes the internal server to send replies back to the Fonera, instead of directly to the client. Care should be taken to only apply the SNAT to packets that need it (i.e., come from the internal network). Using SNAT in this way screws up request logging on the server, since all requests seem to come from the Fonera, the server never learns the real source of the request. As an additional not: The current (2.3.6.1) firmware is already selectively applying the DNAT forwarding to packets coming from the WAN port. This means that forwarding from the LAN port just doesn't happen and the above explanation is not completely applicable. Furthermore, I've looked around a bit for implementing this, but there's a few problems: * In the fw_redirect function that adds the forwarding rules, we only know the ""src"" interface, not the ""dst"" interface (which is the one that needs special treatment). * It requires changing the uci_firewall code quite a bit (and also the meaning of 'redirect' entries in the firewall uci config. This might cause problems on the long run, when upgrading to a newer OpenWRT version. Even with the above problems, it seems it might be useful to implement this anyway. The main advantage is that people can actually test their port forwards from their internal network. Currently a lot of people think their port forwards don't work because they (only) test from their local network...",matthijs 3,1043,SMS function for USB UMTS stick - 3g modems,fon-network-3g,N/A,,enhancement,,investigate,2011-05-07T22:01:16Z,2013-01-23T04:32:33Z,The 3G usb Stick is also used to recive e.g. SMS from my provider in Germany. I like to receive SMS throuh the Fonera 2.0n. There should be an Menu which shows the inbox of the received SMS. It would be great if you can edit it in the next version.,oweee@… 3,1094,Support 3G dongle: ZTE MF190,fon-network-3g,N/A,,enhancement,,investigate,2011-10-02T13:36:22Z,2012-12-20T17:28:01Z,"usb stick is recognized as umts modem, entering PIN is working but no internet connection to the network. tested with vodafone and o2. tried with built-in germany-d2 vodafone settings and manual settings ",inferno@… 3,1108,Support 3G dongle: Huawei E367,fon-network-3g,N/A,,enhancement,,investigate,2011-10-19T22:50:20Z,2012-12-20T17:31:14Z,"I have a Huawei E367 3G USB Dongle from the 3 network in the uk, but the dongle doesnt work when plugged into the Fonera. Can Support for this dongle be added, as it supports HSDPA+ for 14mb download speed over the old 7mb HSDPA dongles. Many thanks. :) Could you email me with any updates to this, or give me tips on how to get it working?",samskellern@… 3,1142,Music plugin should support mms and rtsp streams,fon-plugin-music,N/A,,enhancement,,confirmed,2012-01-19T17:53:59Z,2012-01-19T17:54:27Z,"Right now, the music plugin only supports streaming raw audio streams over HTTP. Some radio stations use mms (or the successor, RTSP) for their streams. Supporting these protocols would further enhance the music plugin.",matthijs 3,1143,Support multicast routing / IGMP,fon-network,N/A,,enhancement,,investigate,2012-01-22T13:40:52Z,2013-02-10T21:36:22Z,"How to enable multicast (igmp) on Fonera 2.0n ? I have developers 2.3.7.0 beta 2 firmware installed. Is this possible? I am unable to find any information bout that...",pyvas@… 3,1156,Add 3G dongle types from GUI,fon-network-3g,N/A,,enhancement,,confirmed,2012-03-11T07:34:09Z,2012-12-20T17:49:27Z,"Could you add in Fonera GUI 3G dongle section some new fields to add custom dongle PID/VID and dial number ? Or a field to upload the config of a new dongle as a file? As reference pls look at TP-LINK TL-MR3420, they have such option in GUI. Afaik their routers are GPL, maybe you could simply copy the code also ? TP-LINK routers support hundreds of modems, I think FON could also do it that way tplink does.",mihaly.reg@… 3,1167,port number change for fonera wan services,fon-network,N/A,,enhancement,,confirmed,2012-04-25T18:55:15Z,2012-12-12T11:38:55Z,"Often happens that wan is scanned by hackers on well known ports, to gain root on fonera. With a good password the attacks are rejected but still load fonera and often hangs, a reset is required. Request: define custom ports for all of fonera wan services like ssh, ftp, http/https webui. ",mihaly.reg@… 3,1168,ssh / ftp wrong password max attempts,fon-network,2.3.7.0 beta2,,enhancement,,investigate,2012-04-25T18:58:54Z,2012-12-19T10:10:36Z,"Often wan is scanned by hackers to gain root on ssh. A countermeasure would be to add to a block list ip's os scanner after 5 wrong password attempts and to reject any tcp afterwards. Blacklist could be cleared manually by webgui page > blocklist edit. ",mihaly.reg@… 3,1169,wan services ip white/black list,fon-network,N/A,,enhancement,,confirmed,2012-04-25T19:02:42Z,2012-12-12T11:41:40Z,"often wan is attacked by hackers, a possible countermeasure would be an IP white list and black list. Black list would deny any tcp communication from hosts blacklisted.",mihaly.reg@… 3,1218,Option to set the tx (transmit power) in Milliwatt (mw),fon-wifi,N/A,,enhancement,,investigate,2012-09-04T20:50:26Z,2012-12-12T10:35:55Z,"Please add an option to set the transmit power in mw. For exmaple in three 25 mw steps starting with 50 mw: 50, 75 and 100 mw.",Anonymer-User@… 3,1220,Enhancement: Provide an option to relay broadcast packets,unknown,N/A,,enhancement,,infoneeded,2012-09-08T20:16:02Z,2012-12-20T18:20:31Z,"It would be cool if you could configure to relay broadcast packets between your router and the fonera private wlan network (when working in 'dhcp' mode). For example, it would enable upnp/dlna between the 2 subnets. In my case, I would like to use my (network cable connected) dlna server from the private fonera wlan.",thomas.pasch@… 3,1231,Include IPsec/L2TP vpn,unknown,N/A,,enhancement,,confirmed,2012-10-16T19:17:18Z,2012-11-21T10:44:59Z,Since iPhones and iPads do not support OpenVPN it would be nice to include an alternative on the Fonera.,elm@… 3,1245,Support 3G dongle: Huawei E353,fon-network-3g,N/A,,enhancement,,confirmed,2013-01-10T17:35:30Z,2013-01-10T17:35:46Z,"In the next release, we'll be improving the 3G support. On the forum, a user (CC'd) reported succes with the Huawei E353, by making some changes to the dial string. In order to not loose this info, I'm copying it below. {{{ root@Fonera:/etc# vi /Apps/umtsd.lua local f = io.open(""/tmp/chat_umts"", ""w"") if f then f:write(""ABORT \""NO CARRIER\""\n"".. ""ABORT \""NO DIALTONE\""\n"".. ""ABORT \""ERROR\""\n"".. ""ABORT \""NO ANSWER\""\n"".. ""ABORT \""BUSY\""\n"".. ""\""\"" \""ATZ\""\n"".. ""OK \""ATH\""\n"".. ""OK AT+CGDCONT=1,\""IP\"",\""""..apn..""\""\n"".. ""OK \""ATD*99#\""\n"".. ########## change from ATD*99***1# (cribbed from E169) ""\""CONNECT\"" \""\"""") f:close() -- some dummy data local model local vendor local data = ""/dev/ttyUSB0"" local cmd = ""/dev/ttyUSB0"" ############# this did read USB1 at the end (cribbed from E169) local user = """" local pass = """" local apn = ""3internet"" ########### added this, I didn't test it without, but it certainly does work local pin = ""0000"" ########### added this (the default PIN), I didn't test it without, but it certainly does work local since = 0 local mode }}}",matthijs 3,1260,Problem with Fonera 2.0n and different USB 3G dongles in Denmark,fon-network-3g,2.3.7.0 (Paco),,enhancement,,infoneeded,2013-04-06T11:38:33Z,2013-04-24T10:21:50Z,"Please I have purchased a Fonera 2.0n with the (maybe naive) intension of using it as an access point with internet via a USB G3 modem. I had one USB G3 from CBB Denmark and it Works great from a PC, but no success with the Fonera 2.0n. Then, since Oister Denmark is one of the default settings in the Fonera 2.0n (CBB isn't) I purchased a dongle and sim Card from them, but that doesn't work neither. Now frustrated after not getting any support from FON I ask if anybody out there please can help? PS: The led on the usb g3 moden flashes blue indicating that it can find a connection, but won't connect. John ",JFSteffensen@… 3,1298,Support 3G dongle: ZTE MF 645,fon-network-3g,N/A,,enhancement,,investigate,2013-04-25T15:46:43Z,2013-04-25T15:50:20Z,"Hi, I have a modem ZTE MF645 3G that does not work on my Fonera 2.0N Firmware 2.3.7.0. Is there anyway to make it work? A procedure or patch? Please feel free for any comments? Thanks a lot.!",gabriel.schwartz@… 3,516,Allow enabling DHCP server in bridge mode,fon-network,N/A,Firmware 2.3,enhancement,john.crispin@…,investigate,2009-12-15T23:29:07Z,2011-09-08T05:04:10Z,"Hi, i really like the bridge mode, but i have noticed that when you enable it fonera lose the posibility to assign ip based on mac andress... i really like this feature and i wanna ask if is possible to keep it on (with option to disable) when you use bridge mode (this feature can be usefull who have a sucking router like mine that have less options)",Barbon 3,579,Prevent attacks,fon-network,N/A,Firmware 2.3,enhancement,iurgi@…,investigate,2010-02-06T21:18:47Z,2012-12-19T17:05:10Z,"Ssh, Ftp and openvpn can be limited to prevent some attacks. For example using iptables to limit the number of access in a minute.",ilvalle@… 3,585,No information publish with Avahi (ZeroConf),fon-plugin-printer,N/A,Firmware 2.3,enhancement,iurgi@…,investigate,2010-02-09T12:54:47Z,2012-12-19T17:06:53Z,Printer Plugin don't use Avahi for broadcast information (Zeroconf).,korbe@… 3,858,Enhancement: Support USB HD spin-down,fon-base-firmware,2.3.6.0 (Gari),Firmware 2.3,enhancement,,investigate,2010-07-13T07:28:47Z,2012-02-26T02:56:27Z,"At present, hard disks connected to fon2300 by usb never spin down. However, it is easy to change that: by using 'opkg', an openwrt repository, installing (and enabling) 'hd-idle'. See [http://wiki.fon.com/wiki/OPKG/fr] for more information. Please consider to include hd-idle (perhaps with a small web interface) to the standard fon2300 firmware.",thomas.pasch@… 3,869,"Upnp Media server [UPnP AV], feature still missing",fon-plugin-ushare,2.3.6.0 (Gari),Firmware 2.3,enhancement,iurgi@…,investigate,2010-07-22T23:23:14Z,2012-04-03T13:33:57Z,"Ticket #269 was closed because a media-server feature was allegedly included in FW 2.5.x, however I'm using 2.6.3 dev and there's no sign of any media-server functionality. Was it removed? Ushare does not appear to be installed and there is no menu option to enable this feature. Support for an Xbox / PS3 compatible media server would be a killer feature for the device. It would eliminate the need for me to go out and buy a plogoplug or some seperate media-server device.",sal@… 3,911,It could be good to optionally start the OpenVPN management port,fon-plugin-openvpn,2.3.6.1 (Gari jr.),Firmware 2.3,enhancement,,confirmed,2010-09-07T20:45:44Z,2012-09-18T15:13:24Z,"This would be enabled either in the config file with this: {{{ option 'management' '0.0.0.0 1195' }}} Or, given another ticket I filed today, in the init.d script as follows: {{{ // Something to check out whether the device is running in TCP, UDP or BOTH if [ -z $TCP ] then $ARGS_T=""$ARGS_T --management '0.0.0.0 1195' fi if [ -z $UDP ] then $ARGS_U=""$ARGS_U --management '0.0.0.0 1196' fi }}}",JonTheNiceGuy 3,919,Replace Music Plugin with Music Player Deamon (MPD),fon-plugin-music,N/A,Firmware 2.3,enhancement,,confirmed,2010-09-14T06:41:10Z,2010-09-20T10:57:19Z,"Music Player Daemon (MPD) is a flexible, powerful, server-side application for playing music. Through plugins and libraries it can play a variety of sound files while being controlled by its network protocol It is installable on OpenWrt and so should be able to run on Fonera as well! This is a great usibility enhencement for the fonera. Fon could / should add the €2,- Usb soundcards to there webshop to sell with the router.... http://mpd.wikia.com/wiki/OpenWRT_FullInstall http://forum.fon.com/forum/viewtopic.php?f=8&t=409 Good thing that there a numbers of clients. This could be tested without a LUA interface first.... ",Voorstad 3,926,Change/add hostname option in Fonera2.0N,fon-base-firmware,N/A,Firmware 2.3,enhancement,,investigate,2010-09-17T23:24:33Z,2012-06-20T17:00:13Z,"Hi, Please Could you add hostname options in fonera2.0n? Thanks in Advance. ",gabriel.schwartz@… 3,932,Upgrade 2.0g kernel to 2.6.26.8,fon-base-firmware,N/A,Firmware 2.3,enhancement,,confirmed,2010-09-24T15:04:12Z,2012-12-20T13:32:12Z,"The most recent release in the 2.6.26 series is .8. We could consider upgrading to it. Potentially interesting changes are: {{{ commit bb457a9869e945299445f13bf618975d1562ab83 Author: Alan Stern Date: Thu Aug 14 03:55:11 2008 +0000 usb-serial: don't release unregistered minors commit 0282b7f2a874e72c18fcd5a112ccf67f71ba7f5c upstream This patch (as1121) fixes a bug in the USB serial core. When a device is unregistered, the core will give back its minors -- even if the device hasn't been assigned any! The patch reserves the highest minor value (255) to mean that no minor was assigned. It also removes some dead code and does a small style fixup. USB: usb-storage: quirk around v1.11 firmware on Nikon D4 commit b9a097f26e55968cbc52e30a4a2e73d32d7604ce upstream usb-storage: quirk around v1.11 firmware on Nikon D40 https://bugzilla.redhat.com/show_bug.cgi?id=454028 Just as in earlier firmware versions, we need to perform this quirk for the latest version too. Speculatively do the entry for the D80 too, as they seem to have the same firmware problems historically. commit 13f3b97af2f88fab1e36adbc6372b184315fdda3 Author: Alexey Dobriyan Date: Fri Aug 22 17:40:10 2008 +0000 USB: cdc-acm: don't unlock acm->mutex on error path commit 74573ee7096a4ffc2f098108d21c85801b9c7434 upstream On Wed, Jul 23, 2008 at 03:52:36PM +0300, Andrei Popa wrote: > I installed gnokii-0.6.22-r2 and gave the command ""gnokii --identify"" > and the kernel oopsed: > > BUG: unable to handle kernel NULL pointer dereference at 00000458 > IP: [] mutex_unlock+0x0/0xb > [] acm_tty_open+0x4c/0x214 commit 1a5f1e89a9259b8447530f671f7fe70ca1049453 Author: Ralph Loader Date: Mon Oct 13 19:35:38 2008 -0400 V4L/DVB (9053): fix buffer overflow in uvc-video Commit fe6c700ff34e68e1eb7991e9c5d18986d0005ac1 upstream V4L/DVB (9053): fix buffer overflow in uvc-video There is a buffer overflow in drivers/media/video/uvc/uvc_ctrl.c: INFO: 0xf2c5ce08-0xf2c5ce0b. First byte 0xa1 instead of 0xcc INFO: Allocated in uvc_query_v4l2_ctrl+0x3c/0x239 [uvcvideo] age=13 cpu=1 pid=4975 ... A fixed size 8-byte buffer is allocated, and a variable size field is read into it; there is no particular bound on the size of the field (it is dependent on hardware and configuration) and it can overflow [also verified by inserting printk's.] The patch attempts to size the buffer to the correctly. commit 643c65d64a8755fca03ab057e6ea2c87c0cc245d Author: Laurent Pinchart Date: Mon Oct 13 19:33:49 2008 -0400 V4L/DVB (8617): uvcvideo: don't use stack-based buffers for USB transfers. commit 04793dd041bbb88a39b768b714c725de2c339b51 upstream Data buffers on the stack are not allowed for USB I/O. Use dynamically allocated buffers instead. commit 372bd6a0bb40ecf8c3ba96fc25f556e23c0847a1 Author: Laurent Pinchart Date: Mon Oct 13 19:32:03 2008 -0400 V4L/DVB (8498): uvcvideo: Return sensible min and max values when querying a boolean control. commit 54812c77bc830e2dbcb62b4c6d8a9c7f97cfdd1b upstream [required to get the following two patches to apply] Although the V4L2 spec states that the minimum and maximum fields may not be valid for control types other than V4L2_CTRL_TYPE_INTEGER, it makes sense to set the bounds to 0 and 1 for boolean controls instead of returning uninitialized values. }}} There's probably also a handful of stability fixes that could be useful, and of course dozens of changes for hardware or architectures we don't use :-)",matthijs 3,933,Twitter Notification when all downloads are completed,fon-plugin-downloader,N/A,Firmware 2.3,enhancement,,confirmed,2010-09-24T21:32:17Z,2010-09-27T09:52:41Z,Can you add a notification (via twitter) when the download manager finishes to download ALL the files in its list?,giuseppeg88 3,944,webdav file sharing,other,2.3.6.1 (Gari jr.),Firmware 2.3,enhancement,,confirmed,2010-10-16T15:47:23Z,2012-06-16T23:54:32Z,"Please add webdav file sharing on fonera f2n (and f2g if possible). Webdav is supported on Nokia s60 mobile phones, could access files 'on the go' from fonera. Thanks!",mihaly.reg@… 3,957,include an url to the fonera downloader extension for firefox when the user logs in with firefox,fon-plugin-downloader,N/A,Firmware 2.3,enhancement,,confirmed,2010-11-03T10:55:24Z,2010-11-03T11:15:32Z,"Hi I think it would be a nice idea to include an url to: https://addons.mozilla.org/es-ES/firefox/addon/51665/ when the user logs in the fonera 2.0 with firefox as maybe some users don't know about this extension. A possible place for inclusion would be the dowloads page or maybe the plugins section.",javier 3,973,download manager: try downloading again a file in case of error,fon-plugin-downloader,N/A,Firmware 2.3,enhancement,,confirmed,2010-11-17T00:39:27Z,2010-11-18T16:57:27Z,"Sometimes it may happen that when you download a file from megaupload, it doesn't start at the first shot for various problems (file temporarily unavailable, etc.); would be comfortable that the fonera tries downloading these files (after downloading all the other in the list) automatically after a while (and with a maximum number of tries). I think this feature would be useful to all the usual users of the download manager.",giuseppeg88@… 3,982,downloader replacement candidate: pyLOAD,fon-plugin-downloader,2.3.6.1 (Gari jr.),Firmware 2.3,enhancement,,investigate,2010-12-07T15:46:16Z,2011-12-03T00:13:49Z,"Considere replacement of actual downloader. pyload.org pyLoad is a fast, lightweight and full featured download manager for many One-Click-Hoster, container formats like DLC, video sites or just plain http/ftp links. It aims for low hardware requirements and platform independence to be runnable on all kind of systems (desktop pc, netbook, NAS, router). Despite its strict restriction it is packed full of features just like webinterface, captcha recognition, unrar and much more. * completely written in python * low hardware requirements * features many One-Click-Hoster * including premium support, captcha recognition, reconnect feature * DLC, CCF, RSDF support * easily remote accessible via webinterface or GUI * free support at irc or forum * released under GPL ",alfie_original@… 3,997,transmission - preallocation full by default installation,fon-plugin-transmission,2.3.6.1 (Gari jr.),Firmware 2.3,enhancement,,confirmed,2010-12-28T19:39:02Z,2011-12-03T00:21:54Z,"Installing transmission on fonera brings the following setting in settings.json: ""preallocation"": 0, that means 'no preallocation', in other words when a download is added it will create the data files 'on the go', as soon as each file is downloaded. That's bad because after a while the disk will be very fragmented. Change request: by default install transmission with: ""preallocation"": 2, that mean 'full allocation at torrent add', this setting will prevent the fragmentation of disk. Thanks!",mihaly.reg@… 3,1053,Correct isp bandwith in QoS setting. (typing instead of selecting),fon-base-firmware,N/A,Firmware 2.3,enhancement,,confirmed,2011-06-21T15:29:29Z,2013-02-20T23:31:09Z,"I use Developer firmware 2.3.6.1 My ISP bandwith is 60/6 Mbps. In Fonera2.0n Dashboard > Settings > QoS I can only select 50 or 100 Mbps download capacity. Maybe a idea to manually type the bandwith in Dashboard > Settings > QoS. But show if it must be in Mb or KB per seconds(!) to prevent wrong values. Then the QoS can be better adjusted to the actual ISP bandwith. Now i used a ssh session by Putty(telnet) and added this code in telnet session to get the 60Mbps download and 6Mbps upload in Fonera2.0n QoS firmware settings. (I calculate Megabit per second to KiloByte per second) uci set qos.wan.upload=732 uci set qos.wan.download=7324 uci commit qos exit",herrsmoking@… 3,1062,Add AirPlay support,fon-plugins,N/A,Firmware 2.3,enhancement,,investigate,2011-08-12T17:36:14Z,2012-01-02T13:36:58Z,"Can you add the AirPlay support to the fonera using shairport? Here you can found this opensource program https://github.com/albertz/shairport Thank you :)",alex.roc08@… 3,1073,Allow specifying the BSSID in wifi-client mode,fon-network,N/A,Firmware 2.3,enhancement,,confirmed,2011-08-25T10:34:46Z,2012-06-20T14:11:43Z,"If you have a bunch of AP's with the same SSID (say a couple of Fonera's broadcasting MyPlace), then you currently instruct a Fonera to connect to a specific AP. You can only specify the SSID and let wpa_supplicant (2.0g) or the wifi driver (2.0n) decide which AP to connect to. In some cases, you might want to fix this connection to a specific access point (also, it might be needed to prevent the Fonera from connecting to itself, not sure). This would be achieved by specifying the BSSID (MAC address) of the AP to connect to in the wifi-wan settings. This would need to be passed to wpa_supplicant on 2.0g (which should be rather easy). On 2.0n, it should be passed to the wifi driver (and probably to ap_client as well, so it can pass the BSSID on to the wifi driver and can prevent trying to connect when the BSSID wasn't even found).",matthijs 3,1086,Transmission improvements,fon-plugin-transmission,2.3.7.0 beta1,Firmware 2.3,enhancement,,investigate,2011-09-21T08:10:24Z,2011-09-21T11:13:26Z," 1. format torrent var image with ext3 (instead of ext2) 2. move setting.json from the torrent image to the var image 3. mount torrent image in a readonly manner 4. implement an unistall method in fon_image.sh 5. check the md5sum of the downloaded image 1 & 2 allow the 3 3 avoid corruption (transmission writes metadata in the var) 4 allows to write a transmission plugin to update the image 5 avoid corruption If you like I will split the ticket in few different tasks",ilvalle@… 3,1099,Disable private wifi,unknown,2.3.7.0 beta2,Firmware 2.3,enhancement,,confirmed,2011-10-10T06:45:03Z,2013-04-29T12:30:12Z,"Like for the public wifi, it would be great to have the possibility to disable the private wifi as well. [[BR]] For example, this improves the wifi performance when the fonera are used in wifi(-bridge) mode.",ilvalle@… 3,1128,Support Netatalk / AFP (for Time machine on Mac OSX 10.7),other,2.3.7.0 beta1,Firmware 2.3,enhancement,,confirmed,2011-12-09T12:19:58Z,2013-02-17T01:13:58Z,"With Mac OSX Lion, time machine doesn't support a USB disk attached to the fonera. When I try to make a backup it shows this message: ""The network backup disk does not support the required AFP features"". With Snow Leopard, it works.",xacobo@… 3,1164,unrar for fonera,fon-plugins,N/A,Firmware 2.3,enhancement,,confirmed,2012-04-01T14:00:30Z,2012-04-30T19:57:28Z,"Please create an official unrar/unzip plugin for fonera. Scope: downloaded torrents are often rar/zipped, fonera could unzip them by press of button in Fonera GUI, then close GUI and files will be unzipped in the background without using another PC. ",mihaly.reg@… 3,1165,OpenVPN: New feature: site-to-site VPN with two Fonera,fon-plugin-openvpn,N/A,Firmware 2.3,enhancement,,confirmed,2012-04-11T21:11:00Z,2013-01-12T01:17:28Z,"I recently purchased and installed my second Fonera, Fonera N this time! I easily configured OpenVPN to access from my PC to the home network but one thing that I think might be useful is to set up two or more ""Fonera"" to get a site-to-site VPN. OpenVPN package allows this, because of OpenVPN is deep integrated into LaFonera functionality, in my opinion would be inexpensive and very useful to have this functionality (perhaps, wanting to exaggerate, not limited to 2 subnets). I remain available for any questions or concerns. Simone Boniolo",sboniolo@… 3,1179,Add static leases to /etc/hosts for DnsMasq,fon-network,N/A,Firmware 2.3,enhancement,,investigate,2012-06-14T12:15:02Z,2012-12-24T10:35:27Z,"It would be useful to be able to step through luci_ethers.@static_lease[] and add entries to /etc/hosts for each of the .hostname, mapping them to the .ipaddr.","Jon ""The Nice Guy"" Spriggs " 3,1189,Use WAN MAC address for wifi-client,fon-wifi,2.3.7.0 beta3,Firmware 2.3,enhancement,,infoneeded,2012-06-23T17:21:00Z,2013-05-05T19:46:09Z,"It seems like it does not use the specified WAN MAC address for the wifi client mode. Either use this WAN MAC address or create a dedicated option just for wifi client. (dual WAN?:) Reason: I don't want the device to show up as a Fonera device when you do a network search. (so spoof it as a normal PC)",Rafael Vuijk 3,1204,Make Transmission download partition (and path?) configurable,fon-plugin-transmission,N/A,Firmware 2.3,enhancement,,confirmed,2012-07-10T16:38:32Z,2012-07-10T16:39:06Z,"Currently, Transmission always downloads its files to the same partition onto which it is installed. Ideally, one would be able to select a different partition and perhaps also a different path (when working with multiple disks and filesystems, for example). Currently, the start.sh script passes the --download-dir option to transmission when starting it, which resets the download dir on every start: [source:trunk/fon/plugins/plugin-torrent/start.sh#L14] A user can still change the download dir for the current session through the Transmission web interface, but it will be reset when the Transmission daemon is restarted. This change would require the addition of settings display to the Transmission page in the luci WebGUI and the removal of the download directory setting in Transmission's own web interface (to prevent confusion).",matthijs 3,1209,Option to move pppoe reconnect to specific time,fon-base-firmware,N/A,Firmware 2.3,enhancement,,investigate,2012-07-17T22:23:52Z,2012-12-19T09:50:49Z,"In germany (and maybe other countries) the internet providers force a pppoe reconnect after 24 h. This happens exact 24 h after the router connects. If the router was turned on at 3 pm the internet connection will drop at 3 pm on the next day. This is very annoying. Some routers (like AVM Fritzbox) have an option to move the reconnect to a specific time like 5am. Please add an option to move the reconnect to a specific time. This could be achieved by checking the time at the pppoe connect and if its more than 30 mins apart the user specified time schedule a reconnect at the time the user specified. Then an addition reconnect would happen at the time the user requested one and then ever 24h.",elm@… 3,1216,FTP Client capability added to Download Manager (or FTP Client App),fon-plugin-downloader,N/A,Firmware 2.3,enhancement,,confirmed,2012-08-24T13:09:42Z,2012-08-24T21:53:33Z,"Hi folks, after posting in the 2.3.7.0 beta 3 post of the blog, I'm following Matthijs' suggestion to post a ticket here. Ok, so my request is simple in statement but perhaps not too simple at all in implementation... I would love to either have in my Fonera 2.0n: a) A FTP client application or; b) For the download manager to have FTP download capability. I have a seedbox that I access through FTP, and right now download with an ftp client in one of my windows computers at home and usually save the downloaded files in the USB disk in the fonera. Hope this is something you guys could implement. Thanks in advance!",jjromano99@… 3,1252,dav2fs support to enable fonera->owncloud->dropbox uploading,other,N/A,Firmware 2.3,enhancement,,investigate,2013-03-12T21:10:08Z,2013-03-25T18:14:03Z,"by providing dav2fs support on the fonera you could enable valuable data transfer possibilities.[[BR]] upload to dropbox / owncloud / mediacenter / etc. can sometimes take a long time if the user's upload speed is low.[[BR]] the user can save a lot of energy by copying the files to upload to a local hdd connected to the fonera, then running a copy command to the folder where the webdav server has been mounted to.[[BR]] [[BR]] after managing to compile the dav2fs module for v2.3.7.0 rc 1 i have verified it's even possible to upload (unlimited size files!) to dropbox with a simple trick: by using the owncloud dropbox module, mounting the dropbox in owncloud (on a hosted server, php webspace, etc.), and copying the files to the owncloud from fonera by using the dav2fs module (which is actually issuing a simple ""cp"" bash command).[[BR]] [[BR]] as the fonera supports picasa/youtube/etc. upload it would be a logical next step to support webdav servers as well. ",Thomas Horner 3,1296,Custom dns for DHCP clients,fon-base-firmware,N/A,Firmware 2.3,enhancement,,confirmed,2013-04-20T12:42:19Z,2013-04-24T10:48:35Z,"It would be nice to have the possibility, from the web interface, to define a custom dns ip when dhcp mode is set. This new dns will be set as default dns for all clients. ",ilvalle@… 3,1110,Limit number of peers in Transmission to reduce load,fon-plugin-transmission,N/A,Firmware 2.3.8.0,enhancement,,investigate,2011-10-28T15:46:20Z,2013-03-13T19:44:35Z,"My experience tells that the default number of peers and global peers is too much for fonera. I think it can be limited to 3 peers/torrent and max global 100 peers. That will allow to leech/seed 33 torrents with 3 peers per torrent simultanously, it's more then enough. Above these limits fonera will just slow down other services because it's busy with to many peers. 100/3 is tested on F2N, probably for F2G it should be 50/2. ",mihaly.reg@… 3,1250,fonera should check the app images before trying to mount them,fon-plugin-transmission,N/A,Firmware 2.3.8.0,enhancement,,confirmed,2013-03-12T20:24:04Z,2013-03-13T16:02:42Z,"application images are mounted by calling /bin/fon_image.sh inside that shell script the following code is used: {{{ mount_img() { /bin/mkdir -p /tmp/images/${IMG} /bin/mount -o loop -t ext2 ${P}/${FON}/${IMG}.${VERSION}.fmg /tmp/images /bin/sleep 1 /bin/mount -o loop -t ext2 ${P}/${FON}/${IMG}.${VERSION}.var /tmp/images } }}} however, due to unstable usb, power outage, etc. the application images definitely get corrupted from time to time. hence the following code would be extremely beneficial: {{{ mount_img() { /bin/mkdir -p /tmp/images/${IMG} echo ""checking loopback image file system"" /usr/sbin/e2fsck -fy ${P}/${FON}/${IMG}.${VERSION}.fmg /bin/mount -o loop -t ext2 ${P}/${FON}/${IMG}.${VERSION}.fmg /tmp/images /bin/sleep 1 echo ""checking loopback image file system"" /usr/sbin/e2fsck -fy ${P}/${FON}/${IMG}.${VERSION}.var /bin/mount -o loop -t ext2 ${P}/${FON}/${IMG}.${VERSION}.var /tmp/images } }}} of cause the ""echo"" calls are not mandatory... ",Thomas Horner 3,1256,execute user profile script,fon-base-firmware,N/A,Firmware 2.3.8.0,enhancement,,confirmed,2013-03-24T16:33:51Z,2013-03-25T09:05:17Z,"users like to use certain shell command aliases. currently users have to modify /etc/profile directly to add their commands. by implementing the below proposal the file /etc/dropbear/profile could be customized by the user which is then upgrade-safe as well. --- /etc/profile Wed Jun 13 14:30:43 2012 +++ ./etc/profile Sat Oct 13 18:50:14 2012 @@ -13,3 +13,6 @@ [ -x /sbin/arp ] || arp() { cat /proc/net/arp; } [ -z /bin/ldd ] || ldd() { LD_TRACE_LOADED_OBJECTS=1 $*; } + +[ -f /etc/dropbear/profile ] && . /etc/dropbear/profile + ",Thomas Horner 4,26,e-mail notifications,unknown,N/A,,enhancement,iurgi@…,confirmed,2008-12-17T09:32:08Z,2012-12-20T18:20:19Z,"Would be nice to get email notifications of activity on the Fon Hotsopt, such as alien connections, etcétera. Email warning from Fon when your fonera looses conectivity would be nice too.",anonymous 4,229,Scheduler (cron) for services/plugins running on Fonera 2,fon-base-firmware,N/A,,enhancement,,confirmed,2009-03-04T20:53:08Z,2012-12-19T09:51:32Z,"This feature would br the possibility to set up start and finish time for services running on Fonera. For example, setting ftp to be active during the day, torrent client running at nigh, etc... just like cron does. ",decodecoding@… 4,235,daap support,fon-plugins,N/A,,enhancement,iurgi@…,investigate,2009-03-09T10:55:14Z,2012-12-19T09:17:24Z,"support for the Digital Audio Access Protocol so that audiofiles are automatically shared on the network. support for playlistsharing would be awesome. http://en.wikipedia.org/wiki/Digital_Audio_Access_Protocol ",falko.richter@… 4,252,Torrent via RSS,fon-plugin-transmission,N/A,,enhancement,iurgi@…,investigate,2009-04-29T22:32:49Z,2012-12-19T09:44:32Z,"Downloading torrents from an RSS feed would not only give the ability to add your favorite TV show torrents, but also to add new torrents remotely by having your own RSS feed.",sbridge 4,255,Alarm clock,fon-base-firmware,N/A,,enhancement,iurgi@…,investigate,2009-05-02T14:23:06Z,2012-12-19T09:52:18Z,I would love to see an alarm clock plugin for waking you up and playing you favorite internet radio station or mp3 file.,daw@… 4,345,F2 as a security cam,fon-plugin-webcam,N/A,,enhancement,iurgi@…,investigate,2009-07-28T09:59:18Z,2010-05-31T16:16:02Z,"Can be done? Step 1: Take a webcam picture every X seconds, save it to USB HD tmp/mounts/Disc-A1/securitycam/ Step 2: Upload the picture to an ftp server on internet (or whatever upload service) Step 3: Move successfully uploaded pictures to tmp/mounts/Disc-A1/securitycam/uploadok/ This would be a very nice and cheap home security improvement.",mihaly.reg@… 4,366,Add option to set DHCP lease ip range to Luci,fon-network,N/A,,enhancement,iurgi@…,investigate,2009-09-03T19:28:18Z,2010-06-29T13:27:44Z,"Please add options to specify the ip reange for DHCP leases in Luci. Currently, leases are from 192.168.10.2 to 192.168.10.254, but I want to configure that to only uses IP addresses from 192.168.10.100 to 192.168.10.199.",carsten.schuette@… 4,394,"Flickr Uploader: Add tags, description, etcetera",fon-plugin-flickr,N/A,,enhancement,iurgi@…,confirmed,2009-09-29T10:29:48Z,2010-05-31T18:06:03Z,"It would be great to be able to add tags and descriptions to the group of photos uploaded to Flickr by La Fonera so no need to do it later on Flickr's web. Thanks ",decodecoding@… 4,465,traffic spend with 3G,fon-network-3g,N/A,,enhancement,iurgi@…,confirmed,2009-11-16T12:39:52Z,2012-12-19T12:58:34Z,"Hi, is it possible to keep recording the spend bytes over 3G during eg reboots? As I'm only allowed to use upto 500mbyte/weekend and the operator insists there is software on the stick that can keep me informed of this...which is not the case when used on a Fonera :( ",steven@… 4,554,Add USB/IP capabilities,fon-plugins,N/A,,enhancement,iurgi@…,investigate,2010-01-06T11:53:09Z,2012-12-19T16:18:22Z,"USB-over-IP makes it possible to have a centralized USB service, that can be shared over IP. It is an opensource client and server with client portions for Windows and Linux (although I don't know the status of a Mac client) The project is hosted here - http://usbip.sourceforge.net/ There's a walk-through guide of using it - http://www.howtoforge.com/how-to-modify-your-gnu-linux-box-to-serve-as-a-usb-over-ip-server",jon@… 4,588,Megaupload/rapidshare uploads,fon-plugins,N/A,,enhancement,iurgi@…,investigate,2010-02-15T15:22:55Z,2012-12-19T17:08:40Z,"I have the fonera 2.0n, rapidshare/megaupload upload anytime soon? It shouldn't be that complicated as it is already possible to download from these sites. All the best, ",oscardelahoya@… 4,629,Wifi MAC address filtering,fon-wifi,2.3.7.0 rc2,,enhancement,iurgi@…,investigate,2010-04-08T19:29:14Z,2013-03-25T14:58:34Z,"The MAC address filtering for the private network it's a feature that a lot of wifi routers have today, and I simply don't get why the fonera lack support to this feature...",nerevar88@… 4,640,OGG support in the music plugin,fon-plugin-music,N/A,,enhancement,iurgi@…,confirmed,2010-04-10T09:46:36Z,2010-06-17T11:07:06Z,"Hello, I've installed the Music plugin in firmware 2.3.6.0 from http://download.fonosfera.org/plugins/ And I've notice no play button for ogg files. Please add ogg support in the music plugin.",xfreebird@… 4,972,Update opkg / import overlay_root patch,fon-base-firmware,N/A,,enhancement,,investigate,2010-11-16T19:00:11Z,2012-12-20T14:33:44Z,"Currently, opkg has a disk-space checkthat is not sufficient for the Fonera's overlay root filesystem. Opkg checks / by default, which is a ro filesystem. Instead, it should check /jffs2. There is currently a workaround in place to skip the disk check alltogether (see #914), but it would be better to make the check work. OpenWRT has a patch for this. We might be able to update opkg at the same time.",matthijs 4,1249,USB audio with Tascam US-144 sound card,fon-plugin-music,2.3.7.0 (Paco),,enhancement,,investigate,2013-03-02T16:15:03Z,2013-03-12T11:02:37Z,"Hey, I have this sound card and wanted to make it work with Fonera, but it doesn't get detected :( So my first question would be, is there a list of supported sound cards? I tried to dig around a bit and found 2 mentions of Tascam sound cards in DD-WRT source, seems that mine might only be supported with the kernel version 3.4? http://svn.dd-wrt.com/browser/src/linux/ar531x/linux-2.6.20/Documentation/sound/alsa/ALSA-Configuration.txt?rev=5799#L1632 http://svn.dd-wrt.com/browser/src/linux/universal/linux-3.4/sound/usb/midi.c?rev=19285#L1328 Thanks, dain",dain 4,323,ext4 support: backport ext4 driver,fon-base-firmware,N/A,Firmware 2.3,enhancement,iurgi@…,confirmed,2009-07-15T12:08:12Z,2013-02-10T21:32:27Z,"la fonera 2.0 can not mount ext4 file-systems from USB disks. error (from dmesg) : ""EXT3-fs: sda2: couldn't mount because of unsupported optional features (240)."" solution : enable ext4 support in kernel",anonymous 4,1215,”renew ip adress” option/function without restarting router for Fonera2n,fon-web,N/A,Firmware 2.3,enhancement,,confirmed,2012-08-21T17:30:47Z,2012-08-22T06:49:42Z,Please add a ”renew ip adress” button (without the necessity of resetting/restarting the whole router) in the fonera menu or at least a html shortcut for resetting the ip adress.,anonymous 5,226,3G Failover feature,fon-network,N/A,,enhancement,john.crispin@…,confirmed,2009-03-04T08:25:47Z,2010-05-31T14:45:10Z,"it would be great if the 3G usb stick would be used as a failover when the ""internet"" uplink is failing",steven@… 5,368,Ask for twitter settings in the setup wizard,fon-base-firmware,Unknown,,enhancement,iurgi@…,confirmed,2009-09-14T13:53:21Z,2010-05-31T18:09:59Z,"Hi, at initial firmware flash it will ask the master password, the flickr/picasa/facebook/youtube/megadownload/rapidshare passwords but not the twitter password",steven@… 5,1238,Feature request: OwnCloud,fon-base-firmware,N/A,,enhancement,,investigate,2012-12-22T09:22:24Z,2012-12-24T11:47:27Z,It would be great if the Fonera could run ownCloud (http://owncloud.org/).,anonymous 5,615,Twitter Notifications in Other Languages,translations,,Firmware 2.3,enhancement,iurgi@…,confirmed,2010-03-31T12:05:32Z,2011-09-22T09:26:13Z,"I think that twitter notifications should be localised and twitt in spanish if you have the fonera configured in spanish, not in english-",Josemi 3,1295,Stable Advice If You Want The Services Of Legal Counsel ###,unknown,Unknown,,request,,new,2013-04-15T08:44:22Z,2013-04-15T08:44:22Z,"Estate planning requires a very special kind of attorney, person who understands the financial markets and trends, along with how they affect your specific situation. You would be wise to have a legal consultant to guide you on the way, though it could be tempting to draw up your own plans and goals. Read here by what to consider in a great estate lawyer. Ensure that the lawyer you are considering has extensive knowledge in the area of law your situation concerns. There are lots of individuals who hire lawyers centered on other factors, and this is simply not recommended. They may do their best, however the the truth is that the case may become more than they can manage. If a lawyer claims that your case is just a ""slam dunk"", view this as a red flag. It'd be extremely tough for a lawyer to tell something similar to [http://www.mass-criminal.com/ massachusetts criminal defense lawyer] this within an initial discussion. There are generally problems in almost any legal issue that can cause unforeseen delays and increased prices. An attorney who's not up front about any of it kind of thing might not have your best interests at heart. A confident lawyer is fantastic, but before a contract is even signed by you with him person who promises you a win isn't the lawyer you desire to choose. There are way too many not known variables in play to create any kind of assurance, therefore pick a attorney who is ready to be honest with you instead. It's a good idea to find a consult before pursuing any activity if you feel that you could have a legal case. Many lawyers provide a free discussion so make sure that you benefit from this. This permits one to try a few different law firms before choosing an attorney. An excellent idea to consider whenever using an attorney would be to get and decide to try as much accomplished in possible in one meeting. You are likely to spend much more to plan different meetings to talk about multiple issues. Going over several subjects in a single meeting can save you a lot of money. Don't just select the first lawyer you see on the web. It's tempting to think lawyers all do the same thing, however they may differ in expertise and quality. Ask friends what they were represented by him for and if a good lawyer is known by them. Be fussy whenever choosing appropriate support. Everybody else wants to discover the best legal representation for the best price. Nevertheless, keep in mind that often times you get what you pay for and you surely want the most effective results of your case. Do some research concerning the standing of many different solicitors as well as asking acquaintances for personal tips. Any kind of empty offices in your lawyer's practice? That is never a good sign. Do not hesitate to ask the team about bare offices to learn what happened. Unless the team provides you with a rational solution, an worker quitting their job is never a good sign. Before you hire legal counsel, see if any dispute can be resolved by you without one. Often individuals are in a position to solve their problems without having to find a lawyer. If you are incapable of resolve your problem without a lawyer, then it's in your best interest to truly have a lawyer on your side. Though an excellent lawyer could cost hundreds of dollars per hour due to their information and knowledge, there are ways to reduce that cost. Before an emergency does occur creating a solid relationship with an lawyer could put you in the group of a long-term client, creating your hourly rate more reasonable. When you hire an attorney who has done many cases successfully in the area where your situation lies, you'll find yourself saving cash. They will need less hours to accomplish the investigation and legwork necessary, and with a greater odds of success, you will pay less to the lawyer and probably get your case. Don't hesitate to employ somebody else for the rest of the legal procedures, if your attorney is not carrying out a good job. Talk to your lawyer as much as possible before the first hearing and pay close focus on their attitude and words throughout the hearing. If you don't think your lawyer is carrying out a good job with addressing you, a very important thing to accomplish is find somebody else. While you may think that spending more leads to higher quality, it generally does not. You're investing in enough time of the lawyer, and their skill level doesn't necessarily equal their pay rate. Ultimately, it's your case which expands your bill, not their experience the total amount of time they spend. Given that you understand more about how house planning works and how an attorney can help, you can move ahead with a well-informed plan. Do your analysis, find recommendations and get your new lawyer aboard the moment you can.It is never too late to plan your future.Law offices of Scott Bradley. 700 W Center St Suite 4, West Bridgewater, MA. 02379",snowitfcachdi1978 3,1302,No Friends and Family on fon webpage.,fon-web,2.3.7.0 (Paco),,request,,new,2013-05-19T11:58:43Z,2013-05-19T11:58:43Z,"Friends and Family using my hotspot are not shown on the fon webpage. I found someone is hacking my FON_FREE_INTERNET access, more or less by accident and i do not want to give a tutorial here how he did it. I need this functionality to look at the fon webpage to see if there is misuse of my hotspot. No family here and logged on is a problem. Can you please repair this function? Regards OldMan.",hommes.hans@… 3,1255,OScam as Fonera2.0n application.,fon-plugins,N/A,,request,,new,2013-03-16T00:52:26Z,2013-03-18T12:11:13Z,"Hello all. I have a openwrt-fonera2n-squashfs.img image file from [http://www.streamboard.tv/ OScam streamboard] mod. He added the OScam softcam to the fonera2.0n. You can download the fonera2.0n image with OScam included [https://mega.co.nz/#!MJgk1aiZ!GLnE3mEpabr3xI2OuaPga0tjf2lHYSnesvTTN44P4Hw here at MEGA] (unzip the download). OScam = openSource softcam, for decrypting encrypted dvb radio & tv (terrestrial,satellite, coax) If you run this image on a fonera2.0n, and you added a Omnikey usb smartcardreader like the 1021 to the fonera, then the fonera can be used as DVB radio & TV decoder/decrypter ;-) DVB-receivers/pvr's on the network request the fonera OScam, and one of the receivers with sat dish are used to send smartcardupdates back to the fonera oscam to update the smartcard. '''It's fantastic.''' But....OScam can be easily updated. Just disable oscam and overwrite the binary with the newest one that can be found here: [http://download.oscam.cc/index.php?&direction=0&order=mod&directory=1.20_TRUNK/mips-fonera2 MIPS Fonera OScam binary] And how can I update the Fonera firmware without losing the OScam functionality? I think the solution is, make OScam as fon application plugin for dev firmware. If it possible that you fonosfera people can take out the oscam components (the things that are added to run OScam) and put them in a OScam.tar.gz application for fonera2.0n ? That would be so awesome, and i guess that a lot of fonera2.0 and satellite/coax/terrestrial users (example enigma2 users) will be so incredibly happy!",herrsmoking@… 3,1176,Reduce memory usage on 2.0g,fon-base-firmware,2.3.7.0 beta2,Firmware 2.3,task,,investigate,2012-06-13T13:59:02Z,2012-10-04T16:35:02Z,"The current stack of applications in the firmware takes up quite some RAM. Since the 2.0g only has 32MB of RAM, its RAM is sometimes nearly full when booting up already. A particular symptom of this memory usage is that uploading a new firmware trhough the webinterface often does not work and results in an out of memory condition with the oom-killer killl lucid, stopping the firmware upgrade. A simple workaround is to disable samba (Windows network shares), which seems to free up sufficient space to prevent further problems. There is a patch for chillispot in the OpenWRT repository, which reduces the memory requirements of chillispot somewhat, which will be applied soon. This does not seem to be sufficient to prevent the above upgrade problem, though. Samba also uses quite some memory (500K + 700K of heap for smbd and nmbd), so this is a good candidate to look for improvements. lucid is also fairly big (500K on startup, of which 200-400K is duplicated for every request handler process). However, a lot of this memory is probably lua data structures, so it's likely that there's no big ""lump"" of memory that can be reduced somewhere, but instead the memory is fairly distributed among the various lua modules...",matthijs