Modify

Opened 9 years ago

Last modified 6 years ago

#374 investigate enhancement

Support 3G dongle: Huawei K3715

Reported by: 3guser Owned by: iurgi@…
Priority: normal Milestone:
Component: fon-network-3g Version: N/A
Severity: unknown
Cc: gianluca.sperandini@… Hardware: both

Description

Here are the results from commands on the Wiki page. This is for a Huawei K3715, Vodafone-branded. This 3G USB dongle has been tested with Swedish operator Halebop and German Vodafone.

cat /proc/bus/usb/devices

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh?= 3 B: Alloc= 1/800 us ( 0%), #Int= 1, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.26.2 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber?=0000:00:00.1 C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr?= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh?= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1001 Rev= 0.00 S: Manufacturer=HUAWEI Technology S: Product=HUAWEI Mobile C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr?=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms


dmesg

Linux version 2.6.26.2 (blogic@blap4) (gcc version 4.1.2) #10 Tue Apr 21 14:12:05 CEST 2009 CPU revision is: 00019064 (MIPS 4KEc) Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

Entering add_active_range(0, 0, 8192) 0 entries of 256 used Initrd not found or empty - disabling initrd Zone PFN ranges:

Normal 0 -> 8192

Movable zone start PFN for each node early_node_map[1] active PFN ranges

0: 0 -> 8192

On node 0 totalpages: 8192

Normal zone: 64 pages used for memmap Normal zone: 0 pages reserved Normal zone: 8128 pages, LIFO batch:0 Movable zone: 0 pages used for memmap

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/preinit Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29784k/32768k available (1889k kernel code, 2984k reserved, 317k data, 128k init, 0k

highmem) SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects?=0, CPUs=1, Nodes=1 Calibrating delay loop... 183.50 BogoMIPS (lpj=917504) Mount-cache hash table entries: 512 net_namespace: 484 bytes NET: Registered protocol family 16 Radio config found at offset 0xf8(0x1f8) AR531x PCI init... done PCI: fixing up device 0,3,0 PCI: Failed to allocate mem resource #1:4000000@84000000 for 0000:00:03.0 Switched to high resolution mode on CPU 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 ar531x: Registering GPIODEV device gpio_proc: module loaded and /proc/gpio/ created squashfs: version 3.0 (2006/03/15) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 58 io scheduler noop registered io scheduler deadline registered (default) gpiodev: gpio device registered with major 254 gpiodev: gpio platform device registered with access mask FFFFFFFF Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A eth0: Atheros AR231x: 00:18:84:d0:a5:a0, irq 4 ar2313_eth_mii: probed eth0: Marvell 88E6060 PHY driver attached. eth0: attached PHY driver [Marvell 88E6060] (mii_bus:phy_addr=0:1f) cmdlinepart partition parsing not available Searching for RedBoot? partition table in spiflash at offset 0x7d0000 Searching for RedBoot? partition table in spiflash at offset 0x7e0000 8 RedBoot? partitions found on MTD device spiflash Creating 8 MTD partitions on "spiflash": 0x00000000-0x00030000 : "RedBoot?" 0x00030000-0x00040000 : "loader" 0x00040000-0x00660000 : "image" 0x000f2e84-0x00660000 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=4A0000, len=1C0000 0x004a0000-0x00660000 : "rootfs_data" 0x00660000-0x007a0000 : "image2" 0x007e0000-0x007ef000 : "FIS directory" 0x007ef000-0x007f0000 : "RedBoot? config" 0x007f0000-0x00800000 : "boardconfig" Registered led device: gpio0 Registered led device: gpio1 Registered led device: wlan Registered led device: gpio3 Registered led device: gpio4 Registered led device: gpio7 nf_conntrack version 0.5.0 (1024 buckets, 4096 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP vegas registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@…> All bugs added by David S. Miller <davem@…> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 128k freed Please be patient, while OpenWrt? loads ... Algorithmics/MIPS FPU Emulator v1.5 mini_fo: using base directory: / mini_fo: using storage directory: /jffs SCSI subsystem initialized device eth0.0 entered promiscuous mode device eth0 entered promiscuous mode br-lan: port 1(eth0.0) entering learning state br-lan: topology change detected, propagating br-lan: port 1(eth0.0) entering forwarding state usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PPP generic driver version 2.4.2 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@…> IPP2P v0.8.1_rc1 loading ipt_time loading Driver 'sd' needs updating - please use bus_type methods wlan: trunk ath_hal: module license 'Proprietary' taints kernel. ath_hal: 2008-10-02 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC,

TX_DESC_SWAP, DFS, XR) ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk) ath_rate_minstrel: look around rate set to 10% ath_rate_minstrel: EWMA rolloff level set to 75% ath_rate_minstrel: max segment size in the mrr set to 6000 us wlan: mac acl policy registered ath_ahb: trunk Atheros HAL provided by OpenWrt?, DD-WRT and MakSat? Technologies wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps

36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP ath_ahb: wifi0: Atheros 2315 WiSoC: mem=0xb0000000, irq=3 PCI: Enabling device 0000:00:00.1 (0000 -> 0002) ehci_hcd 0000:00:00.1: EHCI Host Controller ehci_hcd 0000:00:00.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:00.1: irq 5, io mem 0x80c21000 ehci_hcd 0000:00:00.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected usb 1-1: new high speed USB device using ehci_hcd and address 2 usb 1-1: configuration #1 chosen from 1 choice usbcore: registered new interface driver usblp usbcore: registered new interface driver usbserial usbserial: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core Initializing USB Mass Storage driver... usb 1-1: USB disconnect, address 2 scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Linux video capture interface: v2.00 usbserial: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: USB Driver for GSM modems: v0.7.2 usbserial: USB Serial support registered for Sierra USB modem usbcore: registered new interface driver sierra sierra: USB Driver for Sierra Wireless USB modems: v.1.2.9c fuse init (API version 7.9) usbcore: registered new interface driver uvcvideo USB Video Class driver (SVN r215) usb 1-1: new high speed USB device using ehci_hcd and address 3 usb 1-1: configuration #1 chosen from 1 choice usb-storage: probe of 1-1:1.0 failed with error -5 option 1-1:1.0: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 ttyusb -> 1 ttyUSB0 option 12D11001 usb-storage: probe of 1-1:1.1 failed with error -5 option 1-1:1.1: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 ttyusb -> 1 ttyUSB1 option 12D11001 usb-storage: probe of 1-1:1.2 failed with error -5 option 1-1:1.2: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 ttyusb -> 1 ttyUSB2 option 12D11001 device ath1 entered promiscuous mode br-lan: port 2(ath1) entering learning state br-lan: topology change detected, propagating br-lan: port 2(ath1) entering forwarding state scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning scsi 4:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 usb-storage: device scan complete scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning scsi 5:0:0:0: Direct-Access HUAWEI MMC Storage 2.31 PQ: 0 ANSI: 2 sd 5:0:0:0: [sda] Attached SCSI removable disk usb-storage: device scan complete usb 1-1: USB disconnect, address 3 ttyusb -> 0 ttyUSB0 option 12D11001 option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 option 1-1:1.0: device disconnected ttyusb -> 0 ttyUSB1 option 12D11001 option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 option 1-1:1.1: device disconnected ttyusb -> 0 ttyUSB2 option 12D11001 option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 option 1-1:1.2: device disconnected usb 1-1: new high speed USB device using ehci_hcd and address 4 usb 1-1: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb 1-1: USB disconnect, address 4 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb 1-1: new high speed USB device using ehci_hcd and address 5 usb 1-1: configuration #1 chosen from 1 choice usb-storage: probe of 1-1:1.0 failed with error -5 option 1-1:1.0: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 ttyusb -> 1 ttyUSB0 option 12D11001 usb-storage: probe of 1-1:1.1 failed with error -5 option 1-1:1.1: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 ttyusb -> 1 ttyUSB1 option 12D11001 usb-storage: probe of 1-1:1.2 failed with error -5 option 1-1:1.2: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 ttyusb -> 1 ttyUSB2 option 12D11001 scsi10 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning scsi 10:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 usb-storage: device scan complete scsi11 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning scsi 11:0:0:0: Direct-Access HUAWEI MMC Storage 2.31 PQ: 0 ANSI: 2 sd 11:0:0:0: [sda] Attached SCSI removable disk usb-storage: device scan complete

Attachments (0)

Change History (2)

comment:1 Changed 9 years ago by matthijs

  • Milestone Requests deleted

Milestone Requests deleted

comment:2 Changed 6 years ago by matthijs

  • Cc gianluca.sperandini@… added
  • Component changed from unknown to fon-network-3g
  • Hardware set to both
  • Severity set to unknown
  • Status changed from new to investigate
  • Summary changed from 3G compatibility to Support 3G dongle: Huawei K3715
  • Type changed from bug to enhancement
  • Version set to N/A

As part of the upcoming 2.3.7.0 firmware release, we're reviewing old open tickets to see if they are still relevant, which is why you get this response now.

We will revamp the 3G point at some point in the future. When this happens, we'll need to revisit supporting this 3G stick as well.

Also, ticket #657 is a duplicate of this ticket.

Add Comment

Modify Ticket

Action
as investigate The owner will remain iurgi@….
Author


E-mail address and user name can be saved in the Preferences.

 
Note: See TracTickets for help on using tickets.